| JaLCDOI | 10.18926/17844 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_43_75.pdf |
| 著者 | 大江 啓太| 小西 正躬| 今井 純| |
| 抄録 | As is well known, an advanced knowledge and know-how are needed in the design and the diagnosis work. Further, human experts can cope with the recent trend of customers needs. Therefore, the design and the diagnosis work have been privately performed in the past, and its information cannot be shared. In addition, the number of experts is decreasing. It is a very important problem to maintain and to extend experts technologies having been built up. For the purpose, methods and systems for technical inheritance of the advanced techniques of the skilled engineers are needed to train the unskilled operators and also can assist skilled operators. In this research, attention is focused on the design of analog filter circuit. To attain the target, the circuit structural classifier system to support design work is developed. Furthermore, simulation technology for hot strip rolling mills based on distributed agents is presented aimed to develop tools for the diagnosis of hot strip rolling mills operation. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2009-01 |
| 巻 | 43巻 |
| 開始ページ | 75 |
| 終了ページ | 92 |
| ISSN | 1349-6115 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002308900 |
| JaLCDOI | 10.18926/46978 |
|---|---|
| フルテキストURL | mfe_37_2_029_044.pdf |
| 著者 | Imajo, Shuya| Konishi, Masami| Imai, Jun| Nishi, Tatsushi| |
| 抄録 | In hot strip rolling mills, the looper control system is automated. However, the looper's behavior tends to be unstable in threading. Therefore, human expert always intervenes and stabilizes the looper's behavior by tuning PID gains and interposing manipulation variable of looper control system. In this paper, we propose a method based on the recurrent neural network to express PID gains tuning action by human. Furthermore, we propose two methods to update the model by learning. To check the effectiveness of the proposed learning methods, numerical simulation applied to the looper height control is carried out. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2003-03 |
| 巻 | 37巻 |
| 号 | 2号 |
| 開始ページ | 29 |
| 終了ページ | 44 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 80016037880 |
| JaLCDOI | 10.18926/46948 |
|---|---|
| フルテキストURL | mfe_38_1-2_015_027.pdf |
| 著者 | Torigoe, Takashi| Konishi, Masami| Imai, Jun| Nishi, Tatsushi| |
| 抄録 | In these days, mechanical systems are becoming more complex and highly automated. So, there exist wide variety of demands for reliable diagnostic technology. A reliable data analysis and quantitative diagnosis method of mechanical system is necessary for the purpose. In this paper a quantitative diagnosis method for looper height control system has been developed based on neural network technologies. The wavelet transformation is used for pre-processing to analyze characteristics of looper height control system. And, self organizing map neural network is used for the purpose of classification based on the pre-processed data. After that, the classified results are used for quantitative diagnosis in hierarchical neural network. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2004-03 |
| 巻 | 38巻 |
| 号 | 1-2号 |
| 開始ページ | 15 |
| 終了ページ | 27 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 80016785934 |
| JaLCDOI | 10.18926/15269 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_35_47.pdf |
| 著者 | 堂前 行宏| 小西 正躬| 今井 純| Asada, Hideki| Kitamura, Akira| |
| 抄録 | In this paper, an identification method of motor parameters for the diagnosis of rotor bar defects in the squirrel cage induction motor is proposed. It is difficult to distinguish the degree of deterioration by a conventional diagnostic method such as Fourier analysis. To overcome the difficulty, a motor simulator is used to identify the degree of deterioration of rotors in the squirrel cage induction motor. Using this method, the deterioration of rotor bars in the motor can be estimated quantitatively. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2001-03-27 |
| 巻 | 35巻 |
| 号 | 1-2号 |
| 開始ページ | 47 |
| 終了ページ | 51 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307181 |
| フルテキストURL | fulltext.pdf |
|---|---|
| 著者 | Tsunata, Ren| Yokomichi, Keito| Takemoto, Masatsugu| Imai, Jun| |
| キーワード | Variable flux memory motor hybrid excitation motor traction applications EV HEV six-step operation one-pulse drive output power density |
| 発行日 | 2023-08-03 |
| 出版物タイトル | IEEE Access |
| 巻 | 11巻 |
| 出版者 | Institute of Electrical and Electronics Engineers |
| 開始ページ | 82024 |
| 終了ページ | 82036 |
| ISSN | 2169-3536 |
| 資料タイプ | 学術雑誌論文 |
| 言語 | 英語 |
| OAI-PMH Set | 岡山大学 |
| 論文のバージョン | publisher |
| DOI | 10.1109/ACCESS.2023.3301809 |
| Web of Science KeyUT | 001047221300001 |
| 関連URL | isVersionOf https://doi.org/10.1109/ACCESS.2023.3301809 |
| JaLCDOI | 10.18926/14083 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_41_1_44.pdf |
| 著者 | 前野 良太| 小西 正躬| 今井 純| |
| 抄録 | Petri net model is a frequently-used versatile tool which can represent a widely discrete event system. However, when the scale of the system becomes large, the calculation time for solving optimal problem (optimal firing sequence problem) is markedly increased. In this paper, we propose an approximation method that achieves the efficiency improvement of the solution by decomposing the Petri net for solving the optimal firing sequence problem. A timed Petri Net is decomposed into several subnets in which the optimal firing sequence for each subnet is solved by Dijkstra’s algorithm in polynomial computational complexity. The effectivity of the proposed method is verified by numerical experiments for the flowshop schedule problem. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2007-01 |
| 巻 | 41巻 |
| 号 | 1号 |
| 開始ページ | 44 |
| 終了ページ | 51 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002308128 |
| JaLCDOI | 10.18926/14065 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_42_91.pdf |
| 著者 | Ryohei, Hamana| 小西 正躬| 今井 純| |
| 抄録 | Various kind of productions are made in semiconductor fabrications, where it employs the production system with multiprocesses and multiple Automated Guided Vehicles(AGVs) for transportation. It is difficult to optimize planning of production and transportation simultaneously because of the complicated flow of semifinished products. This paper describes the formulations of production scheduling, transportation routing and sequence planning of material handling system, and algorithm for simultaneous optimization of plannings by using solution space reduction and simulated annealing method. In this paper, all production system is decomposed to the production scheduling problem, transportation routing problem by AGVs and sequence planning of material handling system with managing stockers and buffers. Production scheduling problem and transportation routing problem are solved by the optimization algorithm using the decomposition routing problem. Sequence planning of material handling robot problem is solved by the algorithm using simulated annealing method. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2008-01 |
| 巻 | 42巻 |
| 号 | 1号 |
| 開始ページ | 91 |
| 終了ページ | 103 |
| ISSN | 0475-0071 |
| 言語 | 日本語 |
| 論文のバージョン | publisher |
| NAID | 120002308279 |
| JaLCDOI | 10.18926/46947 |
|---|---|
| フルテキストURL | mfe_38_1-2_005_014.pdf |
| 著者 | Ishimaru, Kazuhito| Konishi, Masami| Imai, Jun| Nishi, Tatsushi| |
| 抄録 | Temperature distribution in the reactor furnace is mainly operated by gas blowing from multiple tuyeres and material charge distribution. The objective of our research is obtain the optimal profile of gas flow to control temperature distribution in the reactor furnace in the shortest possible time. We formulated the optimization problem to reduce deviation of temperature distribution from its desired one in the reactor furnace. Based on the formulation, gas blow conditions are optimized by a sequential quadratic programming method to realize the desired temperature distribution. The validity of the method was checked through numerical experiments. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2004-03 |
| 巻 | 38巻 |
| 号 | 1-2号 |
| 開始ページ | 5 |
| 終了ページ | 14 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 80016785933 |
| 著者 | Tsunata, Ren| Takemoto, Masatsugu| Imai, Jun| Saito, Tatsuya| Ueno, Tomoyuki| |
|---|---|
| キーワード | Aspect ratio axial-flux machine axial-gap motor cooling high efficiency mass production PMSM radial-flux machine soft magnetic composite thermal characteristic |
| 備考 | © 2023 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.| This fulltext file will be available in Mar. 2025.| |
| 発行日 | 2023-03-13 |
| 出版物タイトル | IEEE Transactions on Industry Applications |
| 巻 | 59巻 |
| 号 | 3号 |
| 出版者 | Institute of Electrical and Electronics Engineers (IEEE) |
| 開始ページ | 3353 |
| 終了ページ | 3367 |
| ISSN | 0093-9994 |
| NCID | AA00667900 |
| 資料タイプ | 学術雑誌論文 |
| 言語 | 英語 |
| OAI-PMH Set | 岡山大学 |
| 著作権者 | © 2023 IEEE. |
| 論文のバージョン | author |
| DOI | 10.1109/tia.2023.3255845 |
| Web of Science KeyUT | 001061319100099 |
| 関連URL | isVersionOf https://doi.org/10.1109/tia.2023.3255845 |
| JaLCDOI | 10.18926/14148 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_39_1_28.pdf |
| 著者 | 石丸 和史| 小西 正躬| 今井 純| 西 竜志| |
| 抄録 | In reactor furnace, due to high temperature and high pressure, data can be measured only near the furnace wall. In this paper, the way to estimate temperature distribution in a reactor furnace using measured data near the furnace walls and to control temperature distribution to the desired temperature distribution was studied. In the estimation, SQP method is employed using measured data near the furnace walls. As the result, the whole temperature distribution in a furnace could be obtained from such limited data. Furthermore, to control the temperature distribution in a reactor furnace, gas flow from multiple tuyeres and supplying material for controlling temperature distribution in a reactor furnace were determined by the SQP method. It was shown that temperature distribution in a furnace was regulated to achieve various desired distribution. Thus, it was verified that complicated temperature distribution in a reactor furnace could be controlled by combining furnace simulation and SQP method. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2005-01 |
| 巻 | 39巻 |
| 号 | 1号 |
| 開始ページ | 28 |
| 終了ページ | 39 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002308270 |
| JaLCDOI | 10.18926/14146 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_39_1_21.pdf |
| 著者 | 鳥越 崇史| 小西 正躬| 今井 純| 西 竜志| |
| 抄録 | In this paper, neuro based intelligent diagnosis methods for electro-mechanical control system are proposed. A self organizing map neural network (SOM) is used to classify measured data of the target system as a qualitative diagnostic method. Besides of the above procedure, it is expected to attain more efficient maintenance by a quantitative estimation of failure. For the purpose, new method is proposed using a hierarchical neural network (HNN). In the method, classified results by SOM are processed for the quantitative diagnosis. Hierarchical neural network can identify inner structure of the relations between failure causes and its results that enables a quantitative diagnosis. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2005-01 |
| 巻 | 39巻 |
| 号 | 1号 |
| 開始ページ | 21 |
| 終了ページ | 27 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002308342 |
| 著者 | Imai, Jun| Ando, Yasuaki| 小西 正躬| |
|---|---|
| 発行日 | 2003-12 |
| 出版物タイトル | Decision and Control |
| 資料タイプ | 学術雑誌論文 |
| JaLCDOI | 10.18926/46967 |
|---|---|
| フルテキストURL | mfe_37_1_001_010.pdf |
| 著者 | Sotobayashi, Ken| Konishi, Masami| Nishi, Tatsushi| Imai, Jun| |
| 抄録 | Auto Guided Vehicles (AGVs) are widely used in a semi-conductor fabricating factory and contribute to the stable production of a high quality semi-conductor products. In the near future, further expansion of the transportation system is expected accompanied with the rapid growth of semi-conductor industries. In such situation, the necessity of performing quick planning of transportation route and transportation control will be elevated. In this paper, practicable planning of the transportation route and transportation control are studied based on the decentralized agent method. Especially, the geometrical sizes of AGVs are considered in the determination of transportation routes and control strategy avoiding the occurrence of mutual collisions or deadlock of AGVs. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2002-11 |
| 巻 | 37巻 |
| 号 | 1号 |
| 開始ページ | 1 |
| 終了ページ | 10 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120003457322 |
| JaLCDOI | 10.18926/47023 |
|---|---|
| フルテキストURL | mfe_36_2_015_042.pdf |
| 著者 | Ohtani, Ryuji| Konishi, Masami| Imai, Jun| Nishi, Tatsushi| |
| 抄録 | In this paper, we studied a planning and scheduling of production system considering demand changes. In the proposed system, planning part determines lot-size and amount of jobs in production. On the other hand, scheduling part determines the production sequence of jobs. In order to treat with the demand changes, both planning and scheduling should work well simultaneously. In the proposed system, preset and real time production control system is newly constructed from the view point of adaptive control. In the system, production planning is modified when the difference between production amount and demand becomes large. Moreover, production schedule is regenerated when the determined schedule is deviated from the prospected one. The scheduling system is characterized as the autonomous decentralized optimization system where each job works as agent and agent searches its appropriate starting time of processing. The effectiveness of the proposed system is confirmed by numerical examples. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2002-03 |
| 巻 | 36巻 |
| 号 | 2号 |
| 開始ページ | 15 |
| 終了ページ | 42 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 80015471209 |
| フルテキストURL | IFAC_49_8_7.pdf |
|---|---|
| 著者 | Imai, Jun| Noso, Katsuyuki| Takahashi, Akiko| Funabiki, Shigeyuki| |
| キーワード | Distributed parameter systems Method of weighted residuals Boundary conditions Reduced-order models |
| 備考 | This is an Accepted Manuscript of an article published by Elsevier| |
| 発行日 | 2016-08-09 |
| 出版物タイトル | IFAC-Papers OnLine |
| 巻 | 49巻 |
| 号 | 8号 |
| 出版者 | Elsevier |
| 開始ページ | 7 |
| 終了ページ | 12 |
| ISSN | 2405-8963 |
| 資料タイプ | 学術雑誌論文 |
| 言語 | 日本語 |
| OAI-PMH Set | 岡山大学 |
| 著作権者 | https://creativecommons.org/licenses/by-nc-nd/4.0/deed.ja |
| 論文のバージョン | author |
| DOI | 10.1016/j.ifacol.2016.07.410 |
| Web of Science KeyUT | 000381505200003 |
| 関連URL | https://doi.org/10.1016/j.ifacol.2016.07.410 |
| フルテキストURL | fulltext.pdf |
|---|---|
| 著者 | Tsunata, Ren| Takemoto, Masatsugu| Imai, Jun| Saito, Tatsuya| Ueno, Tomoyuki| |
| キーワード | Pressing Stator cores Magnetic cores Torque Atmospheric modeling Presses Manufacturing Mass production Axial-flux permanent magnet machine soft magnetic composite (SMC) PMSM tooth-tips torque press process semi-closed slot structure axial gap motor mass production YASA motor shoe |
| 発行日 | 2023-10-04 |
| 出版物タイトル | IEEE Access |
| 巻 | 11巻 |
| 出版者 | Institute of Electrical and Electronics Engineers |
| 開始ページ | 109435 |
| 終了ページ | 109447 |
| ISSN | 2169-3536 |
| 資料タイプ | 学術雑誌論文 |
| 言語 | 英語 |
| OAI-PMH Set | 岡山大学 |
| 著作権者 | © 2023 The Authors. |
| 論文のバージョン | publisher |
| DOI | 10.1109/ACCESS.2023.3321829 |
| Web of Science KeyUT | 001086321100001 |
| 関連URL | isVersionOf https://doi.org/10.1109/ACCESS.2023.3321829 |