JaLCDOI 10.18926/15547
フルテキストURL Mem_Sch_Eng_OU_1_59.pdf
著者 Yamashista Yuhiko| Yokoyama Fumiyoshi| Monobe Kazuo|
抄録 Fujiwara's oriented crystallization method was applied to poly (ethylene oxide) to obtain a uniform texture composed of parallel fibrils which correspond to the structure of a radial direction of spherulites. Two different x-ray diffraction patterns in crystallite orientation of the spherulite radius were obtained. From these patterns and crystallization conditions it could be determined that the spherulite radius has a [401] rotation axis below about 50℃ and two [421] and [421]rotation axes above about 50℃. A reasonable interpretation was given for these two ways of spherulitic crystallization, based on the growth features of lamellar crystals of poly (ethylene oxide). That is, it is concluded that a second order transition in poly (ethylene oxide) lamellar crystals near the temperature of 50℃ is responsible for the change of the rotation axis in spherulite radius.
出版物タイトル Memoirs of the School of Engineering, Okayama University
発行日 1966-03-31
1巻
1号
開始ページ 59
終了ページ 62
ISSN 0475-0071
言語 英語
論文のバージョン publisher
NAID 120002307666
JaLCDOI 10.18926/15546
フルテキストURL Mem_Sch_Eng_OU_1_54.pdf
著者 Moriwake Tosio|
抄録 Condensation of 6-methoxy- and 6-methylthio-2-propionaphthone with t-butyl α-bromoisobutyrate gave the corresponding t-butyl β-hydroxy esters in yields of 80 and 84% respectively. The treatment of the β-hydroxy esters with iodine in the presence of red phosphorus in boiling acetic acid effected reductive cleavage to produce 6-hydroxy- and 6-methylthio-α, α-dimethyl-β-ethyl-2 naphthalenepropionic acid in yields of 33 and 34% respectively. Reduction of the former ester in the presence of palladium-charcoal in acetic acid gave α, α-dimethyl-β-ethyl-6-methoxy-2-naphthalenepropionic acid in a 49% yield.
出版物タイトル Memoirs of the School of Engineering, Okayama University
発行日 1966-03-31
1巻
1号
開始ページ 54
終了ページ 58
ISSN 0475-0071
言語 英語
論文のバージョン publisher
NAID 120002307698
JaLCDOI 10.18926/15545
フルテキストURL Mem_Sch_Eng_OU_1_51.pdf
著者 Moriwake Tosio|
抄録 Condensation of σt -butyl chloroacetate and ketones by means of magnesium in ether or benzene alone was carried out but the excellent yields of P-hydroxy ester could not be obtained, and the results of the condensation of t -butyl bromoacetate and ketones by means of magnesium and mercuric chloride in benzene were also disappointing. When a mixture of benzene and ether was used as solvent in the condensation of t-butyl chloroacetate and ketone in the presence of magnesium and mercuric chloride, the yields of p-hydroxy esters from cyclohexanone and methyl isobutyl ketone were 62 and 71 % respectively, and were comparable with those of other condensing methods.
出版物タイトル Memoirs of the School of Engineering, Okayama University
発行日 1966-03-31
1巻
1号
開始ページ 51
終了ページ 53
ISSN 0475-0071
言語 英語
論文のバージョン publisher
NAID 120002307140
JaLCDOI 10.18926/15544
フルテキストURL Mem_Sch_Eng_OU_1_47.pdf
著者 Takeda Akira| Wada Satosi| Ohmura Yutaka|
抄録 a-Chloro-N-arylisobutyrimidyl chloride (I) reacted with ethyl sodiomalonate to afford N-aryl-2,2-dimethyl-3 carbethoxysuccinimide. This reaction seems to proceed in a different mechanism from that of the synthesis of tetronic acids(2) and is supposed to involve a primary attack of the carbanion at the a-carbon atom of the chloride followed by the cyclization.
出版物タイトル Memoirs of the School of Engineering, Okayama University
発行日 1966-03-31
1巻
1号
開始ページ 47
終了ページ 50
ISSN 0475-0071
言語 英語
論文のバージョン publisher
NAID 120002307888
JaLCDOI 10.18926/15543
フルテキストURL Mem_Sch_Eng_OU_1_44.pdf
著者 Takeda Akira| Torii Sigeru|
抄録 Acetylation of γ,γ-dimethyl-α,β-dicarbethoxybutyrolactone in benzene in the presence of sodium hydride was attempted. The structure of the condensation product was assigned to O-acetyl derivative, which was converted into γ,γ-dimethyl-β-carbethoxy-α-carboxybutyrolactone whose structure is also discussed by IR spectrum.
出版物タイトル Memoirs of the School of Engineering, Okayama University
発行日 1966-03-31
1巻
1号
開始ページ 44
終了ページ 46
ISSN 0475-0071
言語 英語
論文のバージョン publisher
NAID 120002307861
JaLCDOI 10.18926/15542
フルテキストURL Mem_Sch_Eng_OU_1_37.pdf
著者 Takahashi Katsuaki| Tanioka Mamoru| Yoshio Tetsuo|
抄録 Studies were carried out in order to know in some detail the transport phenomena through the interface in the viscous liquid moving in laminar flow. Experiments were carried out using ca. 88% glycerin solution, one added with an acid, and the other with alkali together with a small amount of phenolphthalein. Acidic glycerin solution was supplied to a long transparent cuvette of rectangular cross section through which the liquid was made to move slowly enough to establish the laminar flow, thin cords of coloured basic solution were introduced in the direction normal to the axis of flow at regular time intervals. The so obtained patterns of bending cords shortening in regular succession were photographed also at regular time intervals. The authors attribute the origin of the changing patterns of the cords to the velocity gradient existing in the acidic solution which accelerates the diffusion by increasing the concentration gradient near the cords as well as the increase of the interfacial area, and also the decrease of the thickness of the cords. Based on these idea a mathematical analysis was carried out and was obtained an equation which gives the change of the concentration distribution of two dimensional cords. Fair agreement was obtained between the results of mathematical analysis and those of experiments. Furthermore, the influence of the thickness of the cords, and that of the velocity gradient as well as of the diffusion coefficient on the concentration at the center of the cords were discussed.
出版物タイトル Memoirs of the School of Engineering, Okayama University
発行日 1966-03-31
1巻
1号
開始ページ 37
終了ページ 43
ISSN 0475-0071
言語 英語
論文のバージョン publisher
NAID 120002307624
JaLCDOI 10.18926/15540
フルテキストURL Mem_Sch_Eng_OU_1_29.pdf
著者 Takahashi Teruo|
抄録 In this report, gas absorption by a rotating cylindrical liquid jet, whose water traveling length is short, is considered experimentally. Experiments of absorption are proceeded in pure C0(2) gas and water at 20℃: C0(2) gas is cross-currently contacted with a liquid jet. From experimental results, absorption rate was observed to be large immediately after liquid was spouted from small hole drilled through rotating cylinder.
出版物タイトル Memoirs of the School of Engineering, Okayama University
発行日 1966-03-31
1巻
1号
開始ページ 29
終了ページ 36
ISSN 0475-0071
言語 英語
論文のバージョン publisher
NAID 120002307556
JaLCDOI 10.18926/15539
フルテキストURL Mem_Sch_Eng_OU_1_23.pdf
著者 Yamada Toshiro| Kitagawa Shigeru|
抄録 For assessing the qualities of sheet metal for deep-drawing by the tension test, γ value is adopted generally. However, it is difficult and complicated to obtain the precise value of it. In order to obtain the value precisely and easily, the authors have made trialy the devices to measure directly the elongation and the reductions of width and thickness; these devices are transducers to which the electrical resistance strain gauges are applied. By using these devices, precise, continuous, multipoint and quick measurement can be done. It has been clarified by the continuous measurements that γ values are not the same relating to the elongations. It is recommended that one uses γ value obtained at about 25% elongation.
出版物タイトル Memoirs of the School of Engineering, Okayama University
発行日 1966-03-31
1巻
1号
開始ページ 23
終了ページ 28
ISSN 0475-0071
言語 英語
論文のバージョン publisher
NAID 120002307551
JaLCDOI 10.18926/15538
フルテキストURL Mem_Sch_Eng_OU_1_13.pdf
著者 Kashiwada Yukio| Akiyama Koichi|
抄録 In order to make clear how the efflux angle changes in a small crankcase scavenged engine cylinder and in a large loop scavenged engine cylinder, the inlet flow pattern in the single cycle model cylinder has been observed by a high speed motion camera. In general, the scavenging air stream is not effluent in the designed direction of the scavenging port at comparatively slight opening, and the efflux angle changes in proportion to port opening advance. In a small crankcase scavenged engine cylinder, to keep the scavenging air stream in the direction of the scavenging port it is effective to incline the scavenging air passage between the crankcase and the cylinder, and to make thicker the cylinder wall where located scavenging port. In a large loop scavenged engine cylinder to coincide the scavenging air stream with the direction of the scavenging port in the early stage of the scavenging, it has an effect to set the guide plate the position of 1/2 at port height.
出版物タイトル Memoirs of the School of Engineering, Okayama University
発行日 1966-03-31
1巻
1号
開始ページ 13
終了ページ 22
ISSN 0475-0071
言語 英語
論文のバージョン publisher
NAID 120002307846
JaLCDOI 10.18926/15537
フルテキストURL Mem_Sch_Eng_OU_1_1.pdf
著者 Honda Kazuo| Konaga Tetsuro|
抄録 In the field of mechanical engineering, the need for a simple but effective way of evaluating the fatigue strength and lifetime of structural materials is an important problem with which the design engineers have faced. Accordingly, a cunsiderable amount of investigations have been made in this field. However, the basic nature of fatigue damage and the conditions which lead to the initiation and propagation of fatigue cracks are not sufficiently understood. Nor any satisfactory method of assessing the exact state of fatigue damage has yet been found. X-ray diffraction technique is not a new as the method of experimental study, but has often been adopted for direct and non-destructive observations of change in the local structures of crystalline materials at fundamental research. X-ray technique is one of the most powerful means to investigate the changes of microscopic- structure due to external forces, considering the fatigue phenomena occur on the surface of materials. Accordingly, one of the authors have studied the relations of half-value breadth of X-ray diffraction lines, residual stresses and hardness and number of cycles of fatigue stresses in detail for various sorts of engineering metallic materials. In the results of a number of experiments, it has been found that the variation in half-value breadth showed very regular relation with number of stress cycles, the authors have reported that the lifetime of materials in fatigue could be predicted. Consequently, it needs to investigate whether or not this predicting method is fitted for alloy containg α and β phase, moreover, it is interesting to make clear the fatigue mechanism of such materials which are present two phases having the different yield stress and type of crystal structure.
出版物タイトル Memoirs of the School of Engineering, Okayama University
発行日 1966-03-31
1巻
1号
開始ページ 1
終了ページ 12
ISSN 0475-0071
言語 英語
論文のバージョン publisher
NAID 120002307488
著者 菅井 一男| 蔵本 和成|
発行日 1966
出版物タイトル 岡山大学農学部学術報告
28巻
1号
資料タイプ 紀要論文
著者 渋谷 茂| 木下 恵介|
発行日 1966
出版物タイトル 岡山大学農学部学術報告
27巻
1号
資料タイプ 紀要論文
著者 菅井 一男| 蔵本 和成|
発行日 1966
出版物タイトル 岡山大学農学部学術報告
27巻
1号
資料タイプ 紀要論文
著者 須藤 浩| 内田 仙二|
発行日 1966
出版物タイトル 岡山大学農学部学術報告
27巻
1号
資料タイプ 紀要論文
著者 赤松 誠一|
発行日 1966
出版物タイトル 岡山大学農学部学術報告
27巻
1号
資料タイプ 紀要論文
著者 清久 正夫| 佃 律子|
発行日 1966
出版物タイトル 岡山大学農学部学術報告
28巻
1号
資料タイプ 紀要論文
著者 佃 律子| 清久 正夫|
発行日 1966
出版物タイトル 岡山大学農学部学術報告
28巻
1号
資料タイプ 紀要論文
著者 本多 昇| 岡崎 光良| 小野 豊彦| 梶原 秀巳|
発行日 1966
出版物タイトル 岡山大学農学部学術報告
28巻
1号
資料タイプ 紀要論文
著者 渋谷 茂| 木下 恵介| 河合 英元|
発行日 1966
出版物タイトル 岡山大学農学部学術報告
28巻
1号
資料タイプ 紀要論文
著者 益田 忠雄| 平松 幸雄| 笹本 諄一|
発行日 1966
出版物タイトル 岡山大学農学部学術報告
28巻
1号
資料タイプ 紀要論文