JaLCDOI | 10.18926/14053 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_42_1.pdf |

著者 | Asatani Jun| 甲本 卓也| Toru Fujiwara| Tadao Kasami| |

抄録 | Two typical examples, the (32, 21, 6) and (64, 45, 8) extended code of primitive permuted BCH codes, are considered. The sets of minimum weight codewords are analyzed in terms of Boolean polynomial representation. They are classied by using their split weight structure with respect to the left and right half trellis sections, and for each class, the standard form is presented. Based on the results, we can generate a proper list of the minimum weight codewords of the codes. |

キーワード | Boolean polynomial representation extended BCH codes minimum weight codewords binary shift invariance property |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2008-01 |

巻 | 42巻 |

号 | 1号 |

開始ページ | 1 |

終了ページ | 9 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308333 |

JaLCDOI | 10.18926/14055 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_42_10.pdf |

著者 | 金谷 健一| |

抄録 | The author introduced the "geometric AIC" and the "geometric MDL" as model selection criteria for geometric fitting problems. These correspond to Akaike’s "AIC" and Rissanen's "BIC", respectively, well known in the statistical estimation framework. Another criterion well known is Schwarz’ "BIC", but its counterpart for geometric fitting has been unknown. This paper introduces the corresponding criterion, which we call the "geometric BIC", and shows that it is of the same form as the geometric MDL. We present the underlying logical reasoning of Bayesian estimation. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2008-01 |

巻 | 42巻 |

号 | 1号 |

開始ページ | 10 |

終了ページ | 17 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308447 |

JaLCDOI | 10.18926/14056 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_42_18.pdf |

著者 | 金谷 健一| Yasuyuki Sugaya| |

抄録 | We classify and review existing algorithms for computing the fundamental matrix from point correspondences and propose new effective schemes: 7-parameter Levenberg-Marquardt (LM) search, EFNS, and EFNS-based bundle adjustment. Doing experimental comparison, we show that EFNS and the 7-parameter LM search exhibit the best performance and that additional bundle adjustment does not increase the accuracy to any noticeable degree. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2008-01 |

巻 | 42巻 |

号 | 1号 |

開始ページ | 18 |

終了ページ | 35 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308468 |

JaLCDOI | 10.18926/14060 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_42_53.pdf |

著者 | Chai Hong| 東辻 浩夫| |

抄録 | In order to transfer quantum information, the use of spin chains has been proposed and their transfer characteristics have been analyzed. As one of the latter, the maximum of the transfer probability over sufficiently long time period is often considered important and some examples with high maximum values have been given. In these examples, the coupling between neighboring spins are tuned so as to attain high efficiency. In this article, we discuss the effect of noise on the values of coupling constant. As a result, we propose a system where the efficiency is high and also the effect of noise is small. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2008-01 |

巻 | 42巻 |

号 | 1号 |

開始ページ | 53 |

終了ページ | 55 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308635 |

JaLCDOI | 10.18926/14086 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_41_1_63.pdf |

著者 | 金谷 健一| 菅谷 保之| |

抄録 | The convergence performance of typical numerical schemes for geometric fitting for computer vision applications is compared. First, the problem and the associated KCR lower bound are stated. Then, three well known fitting algorithms are described: FNS, HEIV, and renormalization. To these, we add a special variant of Gauss-Newton iterations. For initialization of iterations, random choice, least squares, and Taubin’s method are tested. Numerical simulations and real image experiments and conducted for fundamental matrix computation and ellipse fitting, which reveals different characteristics of each method. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2007-01 |

巻 | 41巻 |

号 | 1号 |

開始ページ | 63 |

終了ページ | 72 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308585 |

JaLCDOI | 10.18926/14087 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_41_1_73.pdf |

著者 | 金谷 健一| |

抄録 | A rigorous accuracy analysis is given to various techniques for estimating parameters of geometric models from noisy data for computer vision applications. First, it is pointed out that parameter estimation for vision applications is very different in nature from traditional statistical analysis and hence a different mathematical framework is necessary in such a domain. After general theories on estimation and accuracy are given, typical existing techniques are selected, and their accuracy is evaluated up to higher order terms. This leads to a “hyperaccurate” method that outperforms existing methods. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2007-01 |

巻 | 41巻 |

号 | 1号 |

開始ページ | 73 |

終了ページ | 92 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308410 |

JaLCDOI | 10.18926/14122 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_40_1_44.pdf |

著者 | 菅谷 保之| 金谷 健一| 金沢 靖| |

抄録 | Dense point matches are generated over two images by rectifying the two images to align epipolar lines horizontally, and horizontally sliding a template. To overcome inherent limitations of 2-D search, we incorporate the “naturalness of the 3-D shape” implied by the resulting matches. After stating our rectification procedure, we introduce our multi-scale template matching scheme and our outlier removal technique using tentatively reconstructed 3-D shapes. Doing real image experiments, we discuss the performance of our method and remaining issues. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2006-01 |

巻 | 40巻 |

号 | 1号 |

開始ページ | 44 |

終了ページ | 52 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308593 |

JaLCDOI | 10.18926/14123 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_40_1_53.pdf |

著者 | 金谷 健一| 菅谷 保之| Hanno Ackermann| |

抄録 | In order to reconstruct 3-D Euclidean shape by the Tomasi-Kanade factorization, one needs to specify an affine camera model such as orthographic, weak perspective, and paraperspective. We present a new method that does not require any such specific models. We show that a minimal requirement for an affine camera to mimic perspective projection leads to a unique camera model, which we call a symmetric affine camera, which has two free functions. We determine their values from input images by linear computation and demonstrate by experiments that an appropriate camera model is automatically selected. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2006-01 |

巻 | 40巻 |

号 | 1号 |

開始ページ | 53 |

終了ページ | 63 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308664 |

JaLCDOI | 10.18926/14124 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_40_1_64.pdf |

著者 | 金谷 健一| |

抄録 | This article summarizes recent advancements of the theories and techniques for 3-D reconstruction from multiple images. We start with the description of the camera imaging geometry as perspective projection in terms of homogeneous coordinates and the definition of the intrinsic and extrinsic parameters of the camera. Next, we described the epipolar geometry for two, three, and four cameras, introducing such concepts as the fundamental matrix, epipolars, epipoles, the trifocal tensor, and the quadrifocal tensor. Then, we present the self-calibration technique based on the stratified reconstruction approach, using the absolute dual quadric constraint. Finally, we give the definition of the affine camera model and a procedure for 3-D reconstruction based on it. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2006-01 |

巻 | 40巻 |

号 | 1号 |

開始ページ | 64 |

終了ページ | 77 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308332 |

JaLCDOI | 10.18926/14149 |
---|---|

フルテキストURL | Mem_Fac_Eng_39_1_40.pdf |

著者 | Al-Sehaim, Sulaiman| 小西 正躬| 能勢 和夫| |

抄録 | In this paper, two problems, plant allocation problem and that of transfer routing from plants to customers, are considered simultaneously. Especially, adaptation scheme for emergency cases are checked. To solve these problems, decentralized agent based optimization procedures are used. In our study, oil production and products transfer in Saudi Arabia are treated. Through numerical experiments, practicability of the proposed method is verified. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2005-01 |

巻 | 39巻 |

号 | 1号 |

開始ページ | 40 |

終了ページ | 45 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308505 |

JaLCDOI | 10.18926/14153 |
---|---|

フルテキストURL | Mem_Fac_Eng_39_1_56.pdf |

著者 | 菅谷 保之| 金谷 健一| |

抄録 | We present a new method for extracting objects moving independently of the background from a video sequence taken by a moving camera. We first extract and track feature points through the sequence and select the trajectories of background points by exploiting geometric constraints based on the affine camera model. Then, we generate a panoramic image of the background and compare it with the individual frames. We describe our image processing and thresholding techniques. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2005-01 |

巻 | 39巻 |

号 | 1号 |

開始ページ | 56 |

終了ページ | 62 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308594 |

JaLCDOI | 10.18926/14155 |
---|---|

フルテキストURL | Mem_Fac_Eng_39_1_63.pdf |

著者 | 金谷 健一| |

抄録 | Geometric fitting is one of the most fundamental problems of computer vision. In [8], the author derived a theoretical accuracy bound (KCR lower bound) for geometric fitting in general and proved that maximum likelihood (ML) estimation is statistically optimal. Recently, Chernov and Lesort [3] proved a similar result, using a weaker assumption. In this paper, we compare their formulation with the author’s and describe the background of the problem. We also review recent topics including semiparametric models and discuss remaining issues. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2005-01 |

巻 | 39巻 |

号 | 1号 |

開始ページ | 63 |

終了ページ | 70 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002308366 |

JaLCDOI | 10.18926/15164 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_35_41.pdf |

著者 | Kuroboshi, Manabu| Tanaka, Muneaki| Kishimoto, Suguru| Goto, Kentaro| Tanaka, Hideo| |

抄録 | In 360 females, Bone mineral density (BMD) in lumbar vertebrae (L2-L4) was assessed by quantitative computed tomography (QCT), and the values obtained were compared with the frequency of vertebral transformation or fracture as assessed by lateral scan image (scanogram) by X-ray CT. A correlation was observed between the frequency of vertebral transformation (or fracture) and lumbar BMD values : BMD under 125 mg/cm(3) was observed over 90% of women with vertebral transformation, and BMD under 70mg/cm(3) was found about 50% of them. These results suggest that decrease in BMD in lumbar vertebrae leads to vertebral transformation or fracture. Thus, measurement of BMD by QCT would be very useful in predicting vertebral transformation or fractures. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2001-03-27 |

巻 | 35巻 |

号 | 1-2号 |

開始ページ | 41 |

終了ページ | 46 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002307948 |

JaLCDOI | 10.18926/15166 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_31_1_19.pdf |

著者 | 東辻 浩夫| 岸本 篤也| 東辻 千枝子| |

抄録 | As a model of dusty plasmas in external fields, Yuka.wa system in a one-dimensional external field is analyzed by molecular dynamics simulations and theoretical approaches. It is shown that particles form clear thin layers (sheets) at low temperatures and the number of layers changes discretely with characteristic parameters of the system, accompanying the rearrangements of whole system from nearly equipartitioned layers to also nearly equipartitioned layers. The number, positions and populations of layers are obtained as functions of characteristic parameters. The shell (sheet) model which has been successful for confined one-component plasmas is extended to this system and results of numerical experiments are reproduced to a good accuracy. The effect of cohesive energy in each layer is of essential importance to reproduce discrete changes in the number of sheets. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 1996-12-27 |

巻 | 31巻 |

号 | 1号 |

開始ページ | 19 |

終了ページ | 33 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002307616 |

JaLCDOI | 10.18926/15346 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_35_9.pdf |

著者 | 阿部 武治| 坪井 智昭| |

抄録 | The evaluation of microscopic inhomogeneity of polycrystalline aluminum is performed by measuring the hardness in respective grains. The recently developed ultra-micro hardness tester is used and the effects of the test pattern, the indentation load and the indenting velocity are examined. Then, the relationship between the increase in the hardness caused by the work hardening and the deformation of respective grains are statistically investigated. The hardness testing mode in which the initial load is applied before the onset of measurement gives more stable results than the testing mode without the initial load. The test condition with the indentation load of 9.8mN and the indentation velocity of 0.2 μm/sec seems to be optimum and gives the least dispersion of the measured values in grains. It is shown that the hardness values of respective grains in polycrystalline aluminum as well as their dispersion increase with the applied plastic strain. Discussion is made on the microscopic deformation behavior of polycrystalline aluminum. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2001-03-27 |

巻 | 35巻 |

号 | 1-2号 |

開始ページ | 9 |

終了ページ | 19 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002307825 |

JaLCDOI | 10.18926/15354 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_34_1.pdf |

著者 | Song Baoyin| 稲葉 英男| 堀部 明彦| Takahashi Takashi| |

抄録 | The experiment for investigating the falling snow melting characteristics of warm water flowing along sheet channels spread on a roof was performed in Tookamachi city, Nigata prefecture from February 6 to February 7, 1995. The sheet surface temperatures at 11 positions in 3 channels were measured. A physical model for a gas-water-snow system was constructed to compare the predicted results with the measured ones. A fully spread uniform water film in the sheet channel was observed in the experiments. The experimental results elucidated that it was feasible to use warm water flowing along sheet channels for melting falling snow on roofs. The temperature drop in the sheet channel mainly depended on the snowfall intensity, atmospheric temperature and wind speed. Under the influence of the roof edge, the temperature drop in the channel next to the side edge was much larger than that in middle channels. A water-snow two phase flow or a snow covered frozen water was experienced temporarily in the lower reaches of the water flowing channel. These suggest that a larger water flow rate is needed for the channel next to the roof edge, and a higher inlet temperature or a greater water flow rate is required for a severe weather condition. There was reasonably good agreement between the measured and predicted water temperatures. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2000-03-27 |

巻 | 34巻 |

号 | 1-2号 |

開始ページ | 1 |

終了ページ | 12 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002307686 |

JaLCDOI | 10.18926/15356 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_34_13.pdf |

著者 | 榊原 精| Tanimoto, Tadashi| Matsushima, Takahisa| Hosokawa, Norio| Kanadani, Teruto| |

抄録 | Repeated tensile fatigue strength of the low temperature age-hardened Al-Zn alloys is investigated varying the specimen thickness. Fatigue strength of the age-hardened specimens decreases with the specimen thickness when the specimen is thinner than a certain thickness, whereas fatigue strength of non age-hardened specimens, i.e., pure aluminum and dilute Al-Zn alloy, does not depend the specimen thickness. The dependence of fatigue strength on the thickness of age-hardened specimen is considered to be caused by the decrease of the strength of specimen as a whole, as a result of increase in volume ratio of the soft surface layer formed after age-hardening with decreasing specimen thickness. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2000-03-27 |

巻 | 34巻 |

号 | 1-2号 |

開始ページ | 13 |

終了ページ | 17 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002307815 |

JaLCDOI | 10.18926/15357 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_35_53.pdf |

著者 | Kim Tae Yong| 加川 幸雄| |

抄録 | Fresnel zone plate lens (FZPL) has widely been used in electromagnetic antenna applications. Most analysis method based on the potential (scalar) wave approximation has been applied to a few very limited and simplified cases. The present paper analyzes the FZPL in more general form including the diffraction and transmission using the method of moments (MoM). The focusing gain characteristics in the oblique incidence as well as in the normal incidence are considered. The MoM solution using the three-dimensional vectorial formulation requires a large memory space for the FZPL as it is operated at a short wavelength. This is simply overcome by using an iterative conjugate gradient method for the numerical evaluation. The MoM solutions are compared with the other solutions. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2001-03-27 |

巻 | 35巻 |

号 | 1-2号 |

開始ページ | 53 |

終了ページ | 61 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002307849 |

JaLCDOI | 10.18926/15362 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_35_97.pdf |

著者 | 山崎 進| 黒瀬 義則| |

抄録 | In this paper, we formulate a new integrity constraint in correlation with 3-valued stable models in an abduction framework based on general logic programs. Under the constraint, not every ground atom or its negation is a logical consequence of the theory and an expected abductive explanation, but some atom may be unspecified as a logical consequence by an adjustment. As a reflection of the integrity constraint with an adjustment, we augment an adjusting derivation to Eshghi and Kowalski abductive proof procedure, in which such an unspecified atom can be dealt with. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2001-03-27 |

巻 | 35巻 |

号 | 1-2号 |

開始ページ | 97 |

終了ページ | 135 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002307812 |

JaLCDOI | 10.18926/15364 |
---|---|

フルテキストURL | Mem_Fac_Eng_OU_35_137.pdf |

著者 | Sakiyama, Takaharu| Yoshimi, Tsuyoshi| Miyake, Akira| Umeoka, Midori| Tanaka, Atsushi| Ozaki, Sho| Nakanishi, Kazuhiro| |

抄録 | A monoacylglycerol lipase (MGL) was purified from Pseudomonas sp. LP7315 by ammonium sulfate precipitation, anion-exchange chromatography, and preparative electrophoresis. The purified enzyme was homogeneous on an SDS-polyacrylamide gel with a molecular mass of 59 kDa. Its hydrolytic activity was confirmed to be specific for monoglycerides: the enzyme did not hydrolyze diand triglycerides. MGL was found to be stable even after l-h incubation at 65℃. The hydrolytic activity depended not only on temperature and pH but also on the type of monoglyceride used. MGL also catalyzed monoglyceride synthesis at 65℃ in a solvent-free two-phase system, in which fatty acid droplets were dispersed in the glycerol phase with a low water content. The synthetic reaction proceeded at a constant rate for approximately 24 h and reached an equilibrium after 48 h of reaction. The initial rate of the synthetic reaction depended on several factors: the type of fatty acid used as the substrate, the amounts of fatty acid and glycerol, and the concentration of MGL in the glycerol phase. To analyze the effects of these factors, a kinetic model was developed based on the assumption that the adsorption equilibrium of MGL molecules at the interface between the two phases is the rate-determining factor for the synthetic reaction. The model was found to yield a good approximation of the initial synthetic rate under various reaction conditions. The analysis suggests that the adsorption behavior of MGL onto the interface had a large effect on the initial rate of the monoglyceride synthesis. |

出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |

発行日 | 2001-03-27 |

巻 | 35巻 |

号 | 1-2号 |

開始ページ | 137 |

終了ページ | 146 |

ISSN | 0475-0071 |

言語 | English |

論文のバージョン | publisher |

NAID | 120002307705 |