JaLCDOI 10.18926/15466
フルテキストURL Mem_Fac_Eng_OU_24_1_1.pdf
著者 吉田 彰| 大上 祐司| 藤井 正浩|
抄録 To clarify the effects of a drive system lubricant additive upon rolling fatigue of rollers manufactured from carburized and hardened steel, three types of oil were used as lubricants: one mineral base oil and the other two mineral base oils to which an S-P additive package and ATF additive package were added, respectively. These specimens were tested for sliding/rolling fatigue and examined for failure on the surface, rolling fatigue strength, and other properties. Roller surface temperatures and inter-roller frictional coefficients were found scarcely affected by the type of oil used. Irrespective of the difference in oil type, failure on the surface was found to be entirely spalling attributable to cracks generated in the subsurface. The depth at which spalling cracks had taken place was found nearly coincident with the depth at which a ratio of reversing orthogonal shear stress to hardness had amplitude A(Tyz/Hv) maximized. These depths were larger as Hertz stress became more prominent. Nevertheless, they were found hardly affected by the type of oil. Although rolling fatigue strength did not show a significant difference dependent upon the type of oil, it may be said that fatigue life would be somewhat negatively affected by an extreme pressure coated film with a content of sulfur and phosphorus.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1989-11-29
24巻
1号
開始ページ 1
終了ページ 12
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307588
JaLCDOI 10.18926/14134
フルテキストURL Mem_Fac_Eng_39_1_1.pdf
著者 Vladimir I. Klochikhin| 藤井 正浩| 吉田 彰|
抄録 Improvement of wear resistance and durability of machine elements with sliding friction pairs is the important tribological problems. The wear resistance has been determined with many configurative parameters, technological parameters, and operational parameters. In this study kinematics of cylindrical joint (CJ), whose motion is reciprocating and rotating, and influence of various parameters on wear resistance of friction pair was investigated.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2005-01
39巻
1号
開始ページ 1
終了ページ 6
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308183
JaLCDOI 10.18926/15498
フルテキストURL Mem_Fac_Eng_OU_25_1_99.pdf
著者 西垣 誠| 竹下 祐二| 河野 伊一郎|
抄録 In this paper, a numerical procedure of determining hydraulic properties in multilayered aquifers are presented. From pumping test data in multilayered aquifers, the coefficient of permeability and specific storage for each aquifer are determined by using a combination of finite element analysis and nonlinear least-squares optimization technique. This study especially points out necessity of stress-flow coupling analysis to explain the behaviors of pressure head in multilayered aquifer during pumping test. As a example, practical pumping test data were evaluate and the coefficients of permeability and specific storage of aquifers and aquitard were obtained.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1990-12-14
25巻
1号
開始ページ 99
終了ページ 109
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307452
JaLCDOI 10.18926/15483
フルテキストURL Mem_Fac_Eng_OU_24_1_107.pdf
著者 河野 伊一郎| 西垣 誠| 竹下 祐二|
抄録 The numerical feasibility of determining soil water retention and hydraulic conductivity functions simultaneously from one-dimensional transient flow experiments in the laboratory by parameter estimation method is evaluated. Soil hydraulic properties are assumed to be represented by van Genuchten's closed-form expressions involving two unknown parameters: coefficients α and n . These parameters are evaluated by nonlinear least-squares fitting of predicted and observed pressure head with time. Gravity drainage experiments are performed for Toyoura standard sand to evaluate the adequacy of this proposed method.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1989-11-29
24巻
1号
開始ページ 107
終了ページ 114
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307749
JaLCDOI 10.18926/15451
フルテキストURL Mem_Fac_Eng_OU_22_45.pdf
著者 河野 伊一郎| 西垣 誠| 竹下 祐二|
抄録 There are two classifications of the mechanism of levee failure caused by floods; local seepage failure and progressive failure. The fundamental causes of levee failure produced by piping and erosion were studied and the safety of river leves during floods evaluated in terms of soil machanics. The critical hydraulic gradient and the process of progressive failure were obtained from one- and two- dimensional model experiments for piping and erosion. Problems inherent in and preventive measures against levee failure are discussed. In particular, effects of the Tsukinowa method, the most representative Japanese flood fighting method, were studied experimentally and improvements proposed.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1988-03-31
22巻
開始ページ 45
終了ページ 62
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307536
JaLCDOI 10.18926/15438
フルテキストURL Mem_Fac_Eng_OU_28_1_61.pdf
著者 竹下 祐二| 河野 伊一郎|
抄録 Knowledge of the unsaturated soil hydraulic properties is essential requirement for prediction of seepage flow and contaminant transport through the vadose zone. Unfortunately, these parameters are usually time consuming and expensive to measure in the field and laboratory. At the present condition, there are few data accumulation for Japanese soils. In this paper, van Genuchten's closed-form expressions are described to estimate unsaturated soil hydraulic properties. To evaluate the adequacy of these expressions, comparisons are performed between observed and calculated unsaturated hydraulic properties for typical Japanese soils.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1993-11-30
28巻
1号
開始ページ 61
終了ページ 69
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307801
JaLCDOI 10.18926/15511
フルテキストURL Mem_Fac_Eng_OU_25_2_55.pdf
著者 Ohkura Akira| 亀山 嘉正| 佐山 隼敏| 鈴木 和彦| Fukumoto Shuichi|
抄録 AHP can handle decision-making problems involving several criteria when some of these are difficult or impossible to compare other than numerically. When a small group of decision makers settle the multi-criteria problem by AHP, the members of group could not often reach an agreement with hierarchic structure involving objectives, criteria, sub-criteria and alternatives because they have different positions, interests, and opinions. Further, the members have different importances for criteria and sub-criteria, and have dissimilar preferences for alternatives. In this article, we reveal the troubleness of AHP in case of being used by a small group of decision makers. Moreover, we proposed a procedure of AHP which the members of group could easily agree with the structure of problem and the weights of criteria etc.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-03-28
25巻
2号
開始ページ 55
終了ページ 67
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307741
JaLCDOI 10.18926/15510
フルテキストURL Mem_Fac_Eng_OU_25_2_39.pdf
著者 Nsunge Felix Chintu| 冨田 栄二| 浜本 嘉輔|
抄録 Velocity distributions and related parameters of transient and steady, turbulent air jets issuing under atmospheric conditions at Mach 0.14, 0.33 and 0.5 have been predicted using Navier-Stokes(N-S) equations for compressible flow and incompressible flow independently with the k-ε model. The closeness and consistence of the results predicted by the N-S equations for compressible and incompressible flows as well as with relevant measurement or similar prediction show that the incompressible flow assumption for at least some subsonic gas jets issuing at velocities higher than Mach 0.3, the general limit for incompressible fluid flow, can be reasonably accurate particularly in the main fully developed flow region. This suggests that the divergence term in source terms of the momentum, turbulence energy and its dissipation rate equations have negligible effects for some seemingly compressible high speed, subsonic free gas jets. The computation time is reduced by at least 18 % when incompressible flow assumption is used.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-03-28
25巻
2号
開始ページ 39
終了ページ 54
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307456
JaLCDOI 10.18926/15508
フルテキストURL Mem_Fac_Eng_OU_25_2_25.pdf
著者 Nsunge Felix Chintu| 冨田 栄二| 浜本 嘉輔|
抄録 A suddenly started cold methane gas jet issuing from a 1 mm diameter orifice into still air at Mach one has been predicted using the two-equation, high Reynolds number version of k-ε turbulence model and SIMPLE algorithm which employs so called primitive variables and a hybrid scheme for treating combined diffusion and convection. Global trends of predicted radial distributions of velocity, temperature, methane concentration in the steady rear part of the transient jet and axial jet tip penetration compare reasonably well with universal profiles representing measurement for the steady jet particularly in the fully developed turbulent core and semi-empirical relation for the transient jet respectively. The prediction scheme has shown reasonably good accuracy especially in prediction of main flow parameters of a transient, high speed compressible gas jet issuing into a dissimilar surrounding gas(binary gas mixture jet).
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-03-28
25巻
2号
開始ページ 25
終了ページ 38
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307676
JaLCDOI 10.18926/15414
フルテキストURL Mem_Fac_Eng_OU_26_1_27.pdf
著者 冨田 栄二| Nsunge Felix Chintu| 浜本 嘉輔|
抄録 Distributions of hydrogen gas concentration in a suddenly started, single shot hydrogen gas jet issuing from a 1 mm diameter injector into still air were measured using laser interferometry method. This unsteady, turbulent free jet flow has also been calculated using the two-equation, high Reynolds number version of k-ε turbulence model and hybrid scheme for treating combined diffusion and convection in the SIMPLE algorithm. The injection pressure was 0.5 MPa for which predicted and measured temporal jet tip penetration distributions indicate that the jet discharged into still air at Mach 0.25. The level of agreement between present prediction and measurement is good in some regions and poor in others.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-11-30
26巻
1号
開始ページ 27
終了ページ 41
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307648
JaLCDOI 10.18926/15391
フルテキストURL Mem_Fac_Eng_OU_27_1_33.pdf
著者 島田 行恭| 鈴木 和彦| 佐山 隼敏|
抄録 Neural nets have recently become the focus of much attention, largely because of their wide range of complex and nonlinear problems. This paper presents a new integrated approach using neural networks for diagnosing process failures. The fault propagation in process is modeled by causal relationships from the fault tree and its minimal cut sets. The measurement patterns required for training and testing the neural network were obtained from fault propagation model. The network is able to diagnose even in the presence of malfunction of certain sensors. We demonstrate via a nitric acid cooler process how the neural network can learn and successfully diagnose the faults.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1992-11-25
27巻
1号
開始ページ 33
終了ページ 44
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307902
JaLCDOI 10.18926/15501
フルテキストURL Mem_Fac_Eng_OU_24_2_67.pdf
著者 名合 宏之| 前野 詩朗|
抄録 Many hydraulic structures are damaged by under flood flow and storm waves year after year. Many cases of dike and breakwater failure are caused by the suck out of sand from behind the revetment. This type of failure will be in close relation to the dynamic behavior of sand bed around the revetment. In this paper, from this point of view, we investigated the basic characteristics of such sand movement by small model tests and tried to explain the hydro- and soil-mechanical mechanism of this phenomenon theoretically.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1990-03-29
24巻
2号
開始ページ 67
終了ページ 78
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307928
JaLCDOI 10.18926/19666
フルテキストURL Mem_Fac_Eng_OU_33_2_45.pdf
著者 Yamada Nobuya| 岡 久雄|
抄録 It is difficult to evaluate a biomechanical properties quantitatively. The authors developed the measurement system of biomechanical properties formerly but it is on a large scale because of the use of personal computer. In this study, the portable measurement system of biomechanical impedance/mobility is developed. To establish a rapid measurement, a random vibration is adopted in input signal. The system consists of the measuring probe, amplifier, and a note-typed personal computer. The measurement probe is developed newly, and has an overall length of 9 ㎝ (without a handle) and a total weight of about 500 g. The measurement program is also developed and is available to any computer which is worked under MS DOS compatible in Windows 95/98 operating system. The biomechanical spectra of thigh, temple and forehead are obtained and they show three typical spectrum patterns.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1999-04-27
33巻
2号
開始ページ 45
終了ページ 50
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309193
JaLCDOI 10.18926/19663
フルテキストURL Mem_Fac_Eng_OU_33_2_39.pdf
著者 Yanagi Makoto| 岡 久雄|
抄録 The acousicmyogram (AMG) is a mechanical phenomenon recorded at the surface of an active muscle. It is used to monitor force production, fatigue, and contractile properties of muscle. In this study, the new electrode with accelerometer for electrostimulation and acoustic detection. It consists of Ag-AgCl active electrode and solid-gel annular groud, and a very light piezoresistive accelerometer. The recorded AMG waveform depends on the pulse amplitude and duration of stimulation current and its lag from the electroatimulation is about 7 ms. The strengh-duration (S-D) curve (the threshold current for stimulation vs. pulse duration) describes the excitability of muscle. The left forearm is electrostimulated by using the same electrode and the muscle vibration (AMG) is recorded with accelerometer. During the muscle fatigue, the S-D curve changes and the current threshold increases under the same pulse duration. The rheobase of S-D curve increases gradually but the chronaxie hardly changes during muscle fatigue.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1999-04-27
33巻
2号
開始ページ 39
終了ページ 44
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309185
JaLCDOI 10.18926/19634
フルテキストURL Mem_Fac_Eng_OU_32_15.pdf
著者 森 政弘| 岡 久雄|
抄録 In a stiffness estimation of living body, an internal structure under the skin influences the measured results. Because a different stiffness of body caused by bones and muscles is obtained. In this paper, by using a measurement system of mechanical impedance, the relations between a viscoelasticity and a distance from the surface of silicone-gel model is calculated. This relation is applied to silicone-gel tumor model and a shape and a viscoelasticity of semi-sphere silicone-gel tumous are estimated. The obtained results are expressed as a reconstructed 3-D image of shape / viscoelasticity. The revised curve-fitting of mechanical impedance and the cancellation of peripheral vibration influence are proposed in order to increase an estimation acccuracy.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1998-04-20
32巻
1-2号
開始ページ 15
終了ページ 22
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309047
JaLCDOI 10.18926/19592
フルテキストURL Mem_Fac_Eng_OU_31_2_29.pdf
著者 岡 久雄| 大島 正和|
抄録 Knee replacement arthroplasty is indicated for the patient with advanced knee pain, knee deformation, and knee functional disorder. The aim of this study was to estimate loosening after a knee replacement arthroplasty. Loosening is measured by a frequency response function, and mobility by random vibration. The modal parameters for the knee joint are obtained by applying a modal analysis to the frequency response function. The values decrease as the knee joint prosthesis loosened. These parameters serve as an index for the condition between a thighbone and the prosthesis. The various indexes will greatly clarify the stage of advance in the loosening of knee-joint prostheses.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1997-03-28
31巻
2号
開始ページ 29
終了ページ 37
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309172
JaLCDOI 10.18926/19591
フルテキストURL Mem_Fac_Eng_OU_31_2_21.pdf
著者 岡 久雄| 中村 貴彦|
抄録 In evaluating the stiffness of skin surface, internal structures such as bone and muscle often affect the measurements. In the present paper, acoustic random vibration is used to estimated the viscoelasticity of a silicone-gel model. This viscoelasticity, which includes two different stiffness strata, is first estimated using a mechanical impedance spectrum, which describes the relation between the depth and viscoelasticity of internal objects. This method is applied to the depth of a silicone-gel tumor model measured by ultrasound imaging and the viscoelasticity of internal gel can be accurately estimated.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1997-03-28
31巻
2号
開始ページ 21
終了ページ 27
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309105
JaLCDOI 10.18926/15495
フルテキストURL Mem_Fac_Eng_OU_24_2_31.pdf
著者 岡 久雄| Isayama Yoshiharu| Nakauchi Makoto| 山本 辰馬|
抄録 A small vibration on the body surface is expected to apply to a clinical examination of the autonomic nervous system. The vibration cannot be found by the naked eyes. It is called a microvibration (MV) or a minor tremor (MT). It is not cleared out why and how the MV occurs, but many papers about its occurrence and clinical application have been published. In this study, the typical spectrum of MV and the various causes of MV occurrence are studied. The relationships of MV with heart rate, muscle contraction and MV are discussed. The power spectrum of MV is obtained by using an autoregressive model.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1990-03-29
24巻
2号
開始ページ 31
終了ページ 40
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307725
JaLCDOI 10.18926/15488
フルテキストURL Mem_Fac_Eng_OU_25_1_37.pdf
著者 Bouzidi, Moncef| 古賀 隆治| 和田 修己| 香川 直己| Hai, Xu| 小坂 恵| Sano, Hiroya|
抄録 Is proposed a tunable diode laser absorption spectrometer system which employs a pulsed current to drive the diode laser still implementing a second-harmonic detection methods enhancing a signal to noise up to 104 times that the case without it. This system affords the lead-salt diode laser a higher operating temperature which allows a more compact deep cooling system. A principle is based on employing a gated integrator between the preamplifier and the lock-in amplifier. Investigations are made on the optimum selection of the gating aperture time interval as determined by response time of the infrared detector and the pulse width of the laser driving current.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1990-12-14
25巻
1号
開始ページ 37
終了ページ 50
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307549
JaLCDOI 10.18926/15479
フルテキストURL Mem_Fac_Eng_OU_24_1_73.pdf
著者 岡 久雄| Isayama Yoshiharu| 山本 尚武| 山本 辰馬|
抄録 There is a small vibration which goes undetected by the naked eyes. It is called a microvibration (MV) or a minor tremor (MT). The MV on the body surface is expected to apply to a clinical examination of the autonomic nervous system. It is not cleared why and how the MV occurs, but there are many papers about its occurrence and clinical application. In this study, MV measuring system, its estimation and basic characteristics are examined. The difference between head MV and thenar MV, individual MV and diurnal and seasonal change are discussed. The power spectrum of MV is obtained using an autoregressive model.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1989-11-29
24巻
1号
開始ページ 73
終了ページ 80
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307633