JaLCDOI 10.18926/14087
フルテキストURL Mem_Fac_Eng_OU_41_1_73.pdf
著者 金谷 健一|
抄録 A rigorous accuracy analysis is given to various techniques for estimating parameters of geometric models from noisy data for computer vision applications. First, it is pointed out that parameter estimation for vision applications is very different in nature from traditional statistical analysis and hence a different mathematical framework is necessary in such a domain. After general theories on estimation and accuracy are given, typical existing techniques are selected, and their accuracy is evaluated up to higher order terms. This leads to a “hyperaccurate” method that outperforms existing methods.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2007-01
41巻
1号
開始ページ 73
終了ページ 92
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308410
JaLCDOI 10.18926/14097
フルテキストURL Mem_Fac_Eng_OU_40_1_9.pdf
著者 貫名 高史| 小西 正躬| 西 竜志| 今井 純|
抄録 Controls of the temperature, pressure and flowing quantity are important for the stable operation of the product quality in the distillation tower. The usual measuring way of product quality estimation is made by the off-line analysis. In this paper, online estimation method of product quality is studied for improving the product quality. The estimation method based on stochastic analysis was developed for online estimation. In this paper, the data of temperature, pressure and flow volum in the distillation tower are treated. As the estimation models, RNN (Recurrent Neural Net Work) and PLS (Partial Least Square Regression Method) were adopted. The actual plant data were used in the analysis. Both PLS and RNN models could compensate each other to improve the accuracy in estimation.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2006-01
40巻
1号
開始ページ 9
終了ページ 15
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308095
JaLCDOI 10.18926/15389
フルテキストURL Mem_Fac_Eng_OU_30_1_121.pdf
著者 Kuk Hun| 谷野 哲三| 田中 雅博|
抄録 In this paper we provide some theoretical results on stability and sensitivity analysis in convex vector optimization. Given a family of parametrized vector optimization problems, the perturbation maps are defined as the set-valued map which associates to each parameter value the set of minimal points (properly minimal points, weakly minimal points) of the perturbed feasible set with respect to an ordering convex cone. Sufficient conditions for the upper and lower semicontinuity of the perturbations map are obtained. We also provide quantitative properties of the perturbation maps under some convexity assumptions.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1995-12-28
30巻
1号
開始ページ 121
終了ページ 131
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307414
JaLCDOI 10.18926/44500
フルテキストURL mfe_045_054_059.pdf
著者 Nekado, Kenta| Takai, Yusuke| Nogami, Yasuyuki| Morikawa, Yoshitaka|
抄録 Recently, pairing–based cryptographies have attracted much attention. For fast pairing calculation, not only pairing algorithms but also arithmetic operations in extension field should be efficient. Especially for final exponentiation included in pairing calculation, squaring is more important than multiplication. This paper considers squaring algorithms efficient for cubic extension field which is often used for pairing implementaions.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2011-01
45巻
開始ページ 54
終了ページ 59
ISSN 1349-6115
言語 English
著作権者 Copyright © by the authors
論文のバージョン publisher
NAID 80021759252
JaLCDOI 10.18926/14061
フルテキストURL Mem_Fac_Eng_OU_42_56.pdf
著者 Miyake Takashi| 東辻 千枝子| Nakanishi Kenta| 鶴田 健二| 東辻 浩夫|
抄録 We analyze the ground state of the two-dimensional quantum system of electrons confined in a parabolic potential with the system size around 100. We map the system onto a classical system on the basis of the classical-map hypernetted-chain (CHNC) method which has been proven to work in the integral-equation-based analyses of uniform unbounded systems and then apply classical numerical simulations. We find that the confined system undergoes the transition to the spin polarized state with the decrease of the average density and the corresponding critical value is as low as rs ∼ 0.3 in terms of the usual rs parameter estimated for the average density. As the ground state for given value of the rs parameter, our data give the critical value for the transition around 20 which is consistent with the known possibility. The advantage of our method is a direct applicability to geometrically complex systems which are difficult to analyze by integral equations. The application to the structure like quantum dots reported here is the first example of such applications.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2008-01
42巻
1号
開始ページ 56
終了ページ 59
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308633
JaLCDOI 10.18926/15444
フルテキストURL Mem_Fac_Eng_OU_26_2_129.pdf
著者 東辻 浩夫|
抄録 The spectrum of Schottky noise in ion storage rings is analyzed as density fluctuations in effectively one-dimensional plasmas. Strong coupling effects in these plasmas are discussed in relation to experimental observations.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1992-03-28
26巻
2号
開始ページ 129
終了ページ 138
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307668
JaLCDOI 10.18926/19622
フルテキストURL Mem_Fac_Eng_OU_31_1_5.pdf
著者 島村 薫| Zhang Chunxiao| 内田 哲也|
抄録 Rigid polymer poly(p-phenylene benzobisthiazole) was crystallized from dilute solution. Electron microscopy showed that upon quenching, flat fibrils with several nm thick were produced. Subsequent heat treatment in solvent changed the fibril into "shish-kebab". On the other hand, by isothermal crystallization, an aggregate of parallel rod-like crystals was obtained. The molecular chains were accommodated normal to the rod. Based on the observation of crystal morphology, the isothermal crystallization mechanism was proposed. Because of regidity of polymer chains and wide distribution of the molecular length, the chain ends were inevitably included within the crystals resulting in crystal defects such as axial shift, lattice curvature and edge dislocation which were directly observed by lattice imaging.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1996-12-27
31巻
1号
開始ページ 5
終了ページ 10
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309167
JaLCDOI 10.18926/19657
フルテキストURL Mem_Fac_Eng_OU_33_2_19.pdf
著者 山本 恭二| Jiao Xuecheng| Jiao Xuezhen|
抄録 A new type of hydrocyclone with a perforated inner cylinder is tested experimentally to study its performance for liquid-solid separation. The size of the cyclone is small so that it may be effective for small particle separation. Two types of the inner cylinder were made : the one has 39.5% void fraction of the perforated surface and the other has 73.5% . The mean particle diameter is 4.5 μ m. It is found that the pressure loss of the cyclone with the inner cylinder is reduced by about 25% compared with that of the ordinary type. The new type cyclone has better separation efficiency.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1999-04-27
33巻
2号
開始ページ 19
終了ページ 24
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309091
JaLCDOI 10.18926/14082
フルテキストURL Mem_Fac_Eng_OU_41_1_31.pdf
著者 濱名 良平| 小西 正躬| 今井 純|
抄録 Various kind of productions are made in semiconductor factories, where it employs the production system with multiprocess and multiple Automated Guided Vehicles(AGVs) for transportation. It is difficult to optimize planning of production and transportation simultaneously because of the complicated flow of semifinished products. This paper describes the formulations of production scheduling and transportation routing, and algorithm for simultaneous optimization of plannings by using logic cuts. The entire problem is decomposed to the master problem and the sub problem. If it derives the infeasible solutions, new constraints are added to the master problem to eliminate the solution area including infeasible solutions. The results of about optimality and computation time by using CPLEX solver are shown compared with conventional decomposition method to check up effectivity of proposed method in small size problem, and about optimality and computaion time for large scale problem.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2007-01
41巻
1号
開始ページ 31
終了ページ 43
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308108
JaLCDOI 10.18926/15406
フルテキストURL Mem_Fac_Eng_OU_27_2_59.pdf
著者 Prokop Jiri| Myojin Sho|
抄録 The paper presents methods for simulation and examination of the performance of a classification yard, including both manual and computer-aided methods. Presented methods are applicable to the simulation and examination of full range of yards of different types and sizes including manually operated as well as highly automated classification yards.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1993-03-25
27巻
2号
開始ページ 59
終了ページ 71
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307384
JaLCDOI 10.18926/19648
フルテキストURL Mem_Fac_Eng_OU_33_2_1.pdf
著者 Omura, Yasuhiro| 飛田 守孝| 榊原 精| 竹元 嘉利|
抄録 Molecular dynamics simulation of nickel crystal under uniaxial tensile and compressive deformation was performed for single nenocrystal model and twinned nanocrystal model composed of 1550 atoms using EAM (embedded atom method) potential with the object of investigating deformation induced phase tranformation (especially twin deformation). In the case of single nanocrystal model, the evolution and development of twin deformation, (111)[11(2)], is observed under compressive loading in [001] direction, whereas either slip or twin deformation is not recognized under tensile loading. In the case of twinned nanocrystal model, twin, (111)[11(2)], decreases and disappears under tensile loading, and develops under compressive loading, It is suggested from the difference of results between single nanocrystal model and twinned nanocrystal model that it is easy for twin to induce local deformation.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1999-04-27
33巻
2号
開始ページ 1
終了ページ 8
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309020
JaLCDOI 10.18926/46975
フルテキストURL mfe_37_2_001_004.pdf
著者 Sakakibara, Akira| Kanadani, Teruto|
抄録 Effect of addition of Fe on the occurrence of serration in Al-12mass%Zn alloys was investigated. Specimens aged at 293K for various periods after quenching from various temperatures (T(Q)), 398K to 823K, were tensile-tested at room temperature. Serration occurred more easily and more remarkably with decreasing T(Q) for as-quenched specimens: in the case that T(Q)=448K serration was observed both for the binary and Fe added alloys, while in the case that T(Q)=573K none of the three alloys showed serration. For the binary alloy serration was observed only when the aging period was short enough, but addition of Fe to the binary alloy prolonged the aging period where serration could be recognized. Aging rate measured by hardness was remarkably retarded with the increase of Fe addition. These results confirm the interpretation that the serration in Al-Zn alloy occurs in the early stage of aging where small GP zones or solute clusters are formed.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2003-03
37巻
2号
開始ページ 1
終了ページ 4
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 80016019142
JaLCDOI 10.18926/46946
フルテキストURL mfe_38_1-2_001_004.pdf
著者 Sakakibara, Akira| Kanadani, Teruto|
抄録 The relationship between occurrence of serration and reversion heat treatment was studied by tensile test on Al-10mass%Zn alloy. Serration was observed for the furnace cooled specimen, but not for the as-quenched one and the shortly aged one, which result is difficult to be interpreted by the Cottrell theory. The stress amplitude in the serration increased with increasing the time of annealing for reversion up to 10ks and then stayed at a constant value which might be interpreted by the Cottrell theory. The stress amplitude in the serration decreased with increasing the annealing temperature, which is contrary to the prediction by the Cottrell theory. The specimen directly annealed without aging and the one annealed after aging agreed well with each other in the tensile strength and the stress amplitude in the serration, which suggests solute clusters as the cause of serration.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2004-03
38巻
1-2号
開始ページ 1
終了ページ 4
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 80016785932
JaLCDOI 10.18926/46977
フルテキストURL mfe_37_2_013_027.pdf
著者 Shibuta, Taizo| Konishi, Masami| Imai, Jun| Nishi, Tatsushi|
抄録 Nowadays, various kind of reactor furnaces are widely used for the production in industry. The raw materials charged into the furnace generate reaction heat produced by blowing gas. Generally speaking, the reaction heat generated in the furnace is remarkably high. Therefore the occurrence of an inappropriate temperature distribution in the furnace may make damege or serious accident of the furnace. This is the motivation of furnace control. The author is considering the application of studied results to the furnace control of Blast Furnace in steel industry. To the propose, the approximated and simplified Macro Model of the Blast Furnace is constructed which has the function of representation of qualitative characteristics of the furnace in dynamical sense. The furnace temperature, distribution greatly effects both on the producting and the product quality of the furnace. Needless to say, stable furnace operation is indispensable for the economical prosperity of the industry. In this paper, macro simulation of the furnace is developed to support the analysis and design of the furnace control. Using the simulator, the stability and the control characteristics for inner furnace temperature distribtion are analised quantitatively.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2003-03
37巻
2号
開始ページ 13
終了ページ 27
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 80015999991
JaLCDOI 10.18926/15488
フルテキストURL Mem_Fac_Eng_OU_25_1_37.pdf
著者 Bouzidi, Moncef| 古賀 隆治| 和田 修己| 香川 直己| Hai, Xu| 小坂 恵| Sano, Hiroya|
抄録 Is proposed a tunable diode laser absorption spectrometer system which employs a pulsed current to drive the diode laser still implementing a second-harmonic detection methods enhancing a signal to noise up to 104 times that the case without it. This system affords the lead-salt diode laser a higher operating temperature which allows a more compact deep cooling system. A principle is based on employing a gated integrator between the preamplifier and the lock-in amplifier. Investigations are made on the optimum selection of the gating aperture time interval as determined by response time of the infrared detector and the pulse width of the laser driving current.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1990-12-14
25巻
1号
開始ページ 37
終了ページ 50
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307549
JaLCDOI 10.18926/19584
フルテキストURL Mem_Fac_Eng_OU_29_1_1.pdf
著者 Uno, Yoshiyuki| Kubota, Shin-ichiro| Yokomizo, Seiichi| Ogata, Kojiro| Tada, Nobuhiko|
抄録 Scribing of copper coated alumina ceramic board with Q-switched YAG laser used for the maskless direct patterning of circuit board is experimentally investigated, which leads to efficient production of trial circuit board. Better dividing of alumina circuit board 655μm in thickness can be attained by the scribing of about 100μm depth. Higher repetition frequency of laser irradiation leads to smaller notch angle and lower breaking load.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1994-11-30
29巻
1号
開始ページ 1
終了ページ 6
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309083
JaLCDOI 10.18926/15445
フルテキストURL Mem_Fac_Eng_OU_26_2_139.pdf
著者 廣瀬 壮一|
抄録 Scattering problems by a penny-shaped crack are solved using a time-domain boundary integral equation method, The crack is located in an infinite homogeneous, isotropic, linearly elastic solid, and is subjected to an oblique incident wave of either P-, SV-, or SH-wave, The hypersingular integral equation is solved to obtain near-field solutions as well as scattered far-fields. The accuracy of the present method is confirmed by comparing the near-field solutions for different arrangement of elements, Scattered far-fields are calculated for various incident waves, and their usefulness in quantitative non-destructive evaluation is discussed.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1992-03-28
26巻
2号
開始ページ 139
終了ページ 150
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307492
JaLCDOI 10.18926/15352
フルテキストURL Mem_Fac_Eng_OU_35_35.pdf
著者 島村 薫| 内田 哲也| 井上 智博|
抄録 Rigid polymer, poly(p-phenylene benzobisthiazole), formed lamellar crystals where the molecular chains were oriented perpendicular to the lamellae. It was supposed that, because of wide distribution in the chain length, the lamellar surface bristled with the chain cilia among which many voids were included. Crystallographically, this region afforded us a transitional structure from full to deficient packings of chains. The structure was analyzed using the scanning probe microscope. In the course the method for imaging one molecular chain end was developed. From the images it was concluded that an isolated long cilius did not move so violently at room temperature.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2001-03-27
35巻
1-2号
開始ページ 35
終了ページ 40
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307784
JaLCDOI 10.18926/46970
フルテキストURL mfe_37_1_025_032.pdf
著者 Kanazawa, Yasushi| Kanatani, Kenichi|
抄録 We present a new method for detecting point matches between two images without using any combinatorial search. Our strategy is to impose various local and non-local constraints as "soft" constraints by introducing their "confidence" measures via "mean-field approximations". The computation is a cascade of evaluating the confidence values and sorting according to them. In the end, we impose the "hard" epipolar constraint by RANSAC. We also introduce a model selection procedure to test if the image mapping can be regarded as a homography. We demonstrate the effectiveness of our method by real image examples.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2002-11
37巻
1号
開始ページ 25
終了ページ 32
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 80015664456
JaLCDOI 10.18926/19606
フルテキストURL Mem_Fac_Eng_OU_33_1_5.pdf
著者 阿部 武治| Namikoshi Ryuji| Nagayama Noriyuki| Takano Yasuju|
抄録 The influence of the slip between the inclusion and the matrix during the plastic deformation of inhomogeneous material with elliptic inclusions is investigated. The material is assumed to be rigid-plastic. The boundary slip region is modeled by assuming lower yield stress for the thin boundary region than those of the inclusion and the matrix. The rigid-plastic finite element method is used for the numerical calculation under the plane strain condition. The effects of the aspect ratio of the inclusion, the yield stress of the boundary region, and the volume fraction of the inclusion on the deformation mode are studied. The patterns of the strain concentration and the averaged flow stress of the inhomogeneous material are also discussed. The results may be helpful for understanding creep or superplastic deformation of metals with inclusions.
キーワード Plasticity Composite Material Sliding Inclusions Rigid-Plastic Deformation Finite Element Method
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1998-11-30
33巻
1号
開始ページ 5
終了ページ 17
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309204