JaLCDOI 10.18926/15420
フルテキストURL Mem_Fac_Eng_OU_26_1_61.pdf
著者 河原 長美| Danno Hideki| Kunimatsu Takao|
抄録 Lake Biwa is the largest lake in Japan, and one of the most important fresh water resources. The Hino River is the fourth largest river among the rivers which flow into Lake Biwa. The eutrophication of the lake has been warned since the 1960s. In order to improve the water quality of the lake, to decrease the loads through rivers is inevitable. Therefore, it is needed to predict the effects of measures to control pollutant loads and the influence of development in the basin on the loads from rivers before developing the basin and taking measures. This paper deals mainly with the model of water quality management for the Hino River and the effects of the development in the basin on the water quality. The model was formulated considering loads from forests, rice paddy fields, households, housing land, industrial factories. Using this model, a calculation system by a microcomputer was developed and the influence of urbanization of the basin was discussed.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-11-30
26巻
1号
開始ページ 61
終了ページ 73
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307182
JaLCDOI 10.18926/15396
フルテキストURL Mem_Fac_Eng_OU_27_1_81.pdf
著者 阿部 宏史|
抄録 This paper aims to examine the impact of JR (Japan Railways) Seto Ohashi Line on residential land value. First, the study examines the trends in land value in the area along JR Seto Ohashi Line by applying the area comparison method. The method estimates the effect of JR Seto Ohashi Line on residential land value by comparing land values between the study area and the Okayama Metropolitan Area. Second, the property value method is applied to measure the effect of railroad construction. The effect is estimated with a residential land-value regression, which is calibrated using land value data along the Seto Ohashi Line. Finally, the results are compared with the empirical studies in the Greater Tokyo Region, and various features of the impact of railroad construction on land value are identified.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1992-11-25
27巻
1号
開始ページ 81
終了ページ 92
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307856
JaLCDOI 10.18926/15424
フルテキストURL Mem_Fac_Eng_OU_29_2_67.pdf
著者 東辻 千枝子| Matsubara Takeo| Obuchi Masumi|
抄録 The π-electron band of C(60) molecule has been obtained by the tight binding approximation. Application of molecular orbital wave functions derived on the basis of the optimized bond orbital model gives, with simpler calculations, the results in satisfactory agreement with those of previous theoretical analyses.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1995-03-27
29巻
2号
開始ページ 67
終了ページ 76
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307408
JaLCDOI 10.18926/15410
フルテキストURL Mem_Fac_Eng_OU_26_1_9.pdf
著者 Uno, Yoshiyuki| Nakajima, Toshikatsu| Okada Minoru|
抄録 Practical utilization of ram type electrical discharge machining in uninflammable fluid has been expected in place of inflammable kerosine type fluid for unmanned operation in a workshop. The electrical discharge machining performance in deionized water is experimentally investigated on the basis of the analysis of the crater generated by a single pulse discharge. The experimental analysis makes it clear that the electrical discharge machining performance in deionized water is greatly affected by the electrode polarity. The metal removal rate in the normal polarity machining is higher than that in reverse polarity machining, while the electrode wear rate in the normal polarity machining is greater than that in reverse polarity machining. Therefore the electrode polarity should be properly selected according to the purpose of machining.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-11-30
26巻
1号
開始ページ 9
終了ページ 20
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307319
JaLCDOI 10.18926/15474
フルテキストURL Mem_Fac_Eng_OU_24_1_53.pdf
著者 尾坂 明義| Takao Seiji| 小田 喜一| 高田 潤| 三浦 嘉也|
抄録 Electrical resistance and X-ray photoelectron depth profile analysis are studied for antimony doped tin oxide films developed on silica, alkali-free and sodalime slide glass substrates. The sodium ions diffused from the substrates to the films prevented the crystal growth of rutile type tin oxide in the film, resulting in the high electrical resistance. A diffusion layer has been detected for each film with diffuse profiles of multi valent cations (Sn, Si or Ca) at the interface of the tin oxide film and substrate. A greater amount of sodium atoms have been detected in the film developed on the soda-lime glass while almost no sodium atoms have been found in those on the other substrates. This can be explained by the diffusion of the sodium ions in the substrate due to a drastic hydronium-sodium exchange mechanism under highly acidic conditions during the dipping and drying processes.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1989-11-29
24巻
1号
開始ページ 53
終了ページ 61
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307279
JaLCDOI 10.18926/14064
フルテキストURL Mem_Fac_Eng_OU_42_79.pdf
著者 Notsu Tadafumi| 小西 正躬| 今井 純|
抄録 The operations of a reactor furnace such as a blast furnace still depend on the experiences and intuitions of skilled operators due to the complexity of internal furnace phenomena and high temperature. There is a great demand for stable operations under the circumstances of a decrease in the number of skilled operators and difficulty in technology inheritance. This paper aims to construct mathematical description for control of a reactor furnace. Further, the linear-quadratic-gaussian control system for a reactor furnace is proposed, which estimates inner furnace temperature distribution using measured data near furnace wall. Temperature distribution of a furnace is controlled based on the estimated inner temperature distribution changing of boundary conditions of a furnace. The practicability of the proposed control method was checked through numerical experiments.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2008-01
42巻
1号
開始ページ 79
終了ページ 90
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308624
JaLCDOI 10.18926/15350
フルテキストURL Mem_Fac_Eng_OU_35_29.pdf
著者 島村 薫| Munesawa Yuhji| 内田 哲也|
抄録 Poly (ethylene-block-vinyl alcohol), which consisted of both hydrophobic and hydrophilic blocks, was prepared by using polyethylene single crystals as starting material. Polyethylene single crystals reacted with fuming nitric acid resulting in long methylene chains with functional groups such as COOH and NO(2) at the ends (the chain length were almost same as the lamellar thickness of polyethylene single crystal). The functionalized methylene chains were allowed to react with 4-aminostyrene to give corresponding amides, i.e., methylene chains with vinyl groups at the ends (macromer). The macromers were extended by block-copolymerization with vinyl acetate, then saponified resulting in PE/PVA block co-polymer. The block copolymer was molded into sheets which were subsequently heat-treated in contact with hydrophilic or hydrophobic media. Depending on the media, the sheet surface changed at high temperature reversibly from hydrophilic to hydrophobic and vice versa. The surface property was fixed by quenching because both blocks were able to crystallize. Thus the surface of this material can be tailored for various purposes at high temperature, and then used in stable at room temperature.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2001-03-27
35巻
1-2号
開始ページ 29
終了ページ 34
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307155
JaLCDOI 10.18926/19624
フルテキストURL Mem_Fac_Eng_OU_31_1_11.pdf
著者 Zhang Chunxiao| Tanigawa Satoshi| 内田 哲也| 島村 薫|
抄録 Poly[(benzo[1,2-d:5,4-d']bissthiazole-2,6-diyl)-1,4-phenylene](cis-PBZT)with a relatively high molecular weight was prepared by a new synthesis route. Properties of the synthesized polymer, such as thermostability, liquid crystallinity etc. were investigated and compared with those of trans-PBZT. cis-PBZT was crystallized from dilute solution and the electron microscopy showed that the precipitate was a rod-like crystal similar to that of trans form. In spite of rigid nature of the back bone, cis-PBZT showed poor crystallinity.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1996-12-27
31巻
1号
開始ページ 11
終了ページ 17
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309203
JaLCDOI 10.18926/17841
フルテキストURL Mem_Fac_Eng_OU_43_55.pdf
著者 井上 真一郎| 小西 正躬| 今井 純|
抄録 In this research, an image processing method and a system for inspection support of a rod figured cutting tool are developed. As is well known, the visual inspection of a cutting tool by image processing is not easy, because cutting blade have a helical blade structure. To cope with the problem, an experimental facility with rotation and longitudinal tool shift functions to enable acquisition of blade surface pictures along a cutting rod is developed. The type of the defect treated in this paper is the spot of coating on blade surface. To judge the quality of the processed image of blade surface, neural network with autonomous learning is used. The processed image of cutting tool is divided into 64 × 64 blocks used for the input to the neural networks. Before input, each block data is preprocessed applying a edge detection filter and a transformation by the discrete fourier transform (DFT). Using these technologies, the experimental inspection system is built and tested to check the capabilities of the inspection algorithms. The diagnostic performance of the surface defect of a cutting tool was confirmed. There remained a problem to mis judge the normal tools as the defect.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2009-01
43巻
開始ページ 55
終了ページ 60
ISSN 1349-6115
言語 English
論文のバージョン publisher
NAID 120002308973
JaLCDOI 10.18926/15490
フルテキストURL Mem_Fac_Eng_OU_25_1_51.pdf
著者 東辻 浩夫|
抄録 The superconductivity proximity effect in the dirty limit is revisited and equations and boundary conditions are obtained for the case of inhomogeneous media with continuously varying characteristic parameters.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1990-12-14
25巻
1号
開始ページ 51
終了ページ 57
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307188
JaLCDOI 10.18926/19585
フルテキストURL Mem_Fac_Eng_OU_29_1_23.pdf
著者 Kawara, Osami| Fukumoto Kohji|
抄録 In this study we investigated the water quality of surface runoff and groundwater runoff from the basins of the Yodo River and the Asahi River based on that separated by a numerical filter. The water quality of the surface runoff is greatly different from the groundwater runoff. The tendency of concentration change in accordance with river discharges is different from each other. The water qtiality of groundwater runoff changes with river discharges clockwise in many cases. The differences of COD and SS originating from those of population and industrial activities in each basin are found in the lower SS concentrations of the surface runoff and the COD cencentrations of the groundwater runoff. The nutrients and chlorine ion were investigated, too.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1994-11-30
29巻
1号
開始ページ 23
終了ページ 34
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309068
JaLCDOI 10.18926/19628
フルテキストURL Mem_Fac_Eng_OU_32_1.pdf
著者 Guo, Changning| Uno, Yoshiyuki| Okada, Akira| Takagi, Takashi|
抄録 Low electrode wear EDM is attained by the adhesion of heat resolved carbon made from kerosine type machining fluid to the electrode end surface. This phenomenon, however, occurs only under long pulse duration. Therefore, the low electrode wear EDM under finishing condition is impossible so far. In the previous paper, the authors developed a turbostratic carbon electrode whose structure is very similar to the heat resolved carbon generated in EDM process and made it clear that the low electrode wear EDM was possible by using the electrode even under finishing condition. In this study, a carbon coated electrode and a SiC coated one which can be made rapidly at low cost were developed and their EDM characteristics were investigated. Experimental analysis pointed it out that both electrodes were effective in reducing electrode wear under finishing condition.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1998-04-20
32巻
1-2号
開始ページ 1
終了ページ 6
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309140
JaLCDOI 10.18926/14088
フルテキストURL Mem_Fac_Eng_OU_41_1_93.pdf
著者 Tarequl Islam Bhuiyan| 中西 真| 藤井 達生| 高田 潤|
抄録 Co-precipitation method has been employed to fabricate neodymium substituted hematite with different compositions from the aqueous solution of their corresponding metal salts. Thermal analysis and X-ray diffraction studies revealed the coexistence of Fe(2)O(3) and Nd(2)O(3) phases up to 1050℃ and formation of solid solution phase among them at 1100℃ and above temperatures, which was evidenced by shifting of the XRD peaks. Unit cell parameters and the cell volumes of the samples were found to increase by adding Nd(3+) ions in the reaction process. FESEM studies showed the suppression of particle growth due to the presence of Nd(3+) ions. Spectroscopic measurement evidenced that neodymium substituted hematite exhibited brighter yellowish red color tone than that of pure α-Fe(2)O(3).
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2007-01
41巻
1号
開始ページ 93
終了ページ 98
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308163
JaLCDOI 10.18926/19636
フルテキストURL Mem_Fac_Eng_OU_32_23.pdf
著者 東辻 浩夫| 岸本 篤也| 東辻 千枝子|
抄録 Parameters characterizing the structure ot confined Yukawa system are estimated for 'dusty plasmas', clouds of charged macroscopic particles formed near the boundary between plasma and the sheath and leviated by negatively biased electrode. When we have dust particles with different ratios of charge to mass, they form a two-dimensional Yukawa mixture or separate two-dimensional one-companent Yukawa systems, depending on the charge density in the sheath and number density of dust particles. In order to provide a basis for numerical simulations on Yukawa mixtures including Coulombic case, we summarize mathematical expressions necessary for molecular dynamics.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1998-04-20
32巻
1-2号
開始ページ 23
終了ページ 41
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002309150
JaLCDOI 10.18926/46949
フルテキストURL mfe_38_1-2_029_032.pdf
著者 Totsuji, Hiroo| Totsuji, Chieko| Ogawa, Takafumi| Tsuruta, Kenji|
抄録 The structure of dust particles in dusty plasmas under microgravity has been analyzed by molecular dynamics simulation. The charge neutrality condition satisfied by the system composed of dust particles and ambient plasma is properly taken into account. It is shown that dust particles form shell structures at low temperatures and the number of shells are obtained as a phase diagram in the plane of two parameters characterizing the system: the number of particles and the strength of screening. It is also shown that these structures are almost independent of the strength of screening.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2004-03
38巻
1-2号
開始ページ 29
終了ページ 32
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 80016863328
JaLCDOI 10.18926/15166
フルテキストURL Mem_Fac_Eng_OU_31_1_19.pdf
著者 東辻 浩夫| 岸本 篤也| 東辻 千枝子|
抄録 As a model of dusty plasmas in external fields, Yuka.wa system in a one-dimensional external field is analyzed by molecular dynamics simulations and theoretical approaches. It is shown that particles form clear thin layers (sheets) at low temperatures and the number of layers changes discretely with characteristic parameters of the system, accompanying the rearrangements of whole system from nearly equipartitioned layers to also nearly equipartitioned layers. The number, positions and populations of layers are obtained as functions of characteristic parameters. The shell (sheet) model which has been successful for confined one-component plasmas is extended to this system and results of numerical experiments are reproduced to a good accuracy. The effect of cohesive energy in each layer is of essential importance to reproduce discrete changes in the number of sheets.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1996-12-27
31巻
1号
開始ページ 19
終了ページ 33
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307616
JaLCDOI 10.18926/46999
フルテキストURL mfe_36_1_041_049.pdf
著者 Totsuji, Hiroo| Kishimoto, Tokunari| Totsuji, Chieko| Tsuruta, Kenji|
抄録 The ground state of spherical clusters of charged particles of one species confined by the three-dimensional parabolic potential is investigated by molecular dynamics simulations with the system size from N = 5000 to N = 1.2 × 10(5) . The cohesive energy per particle is compared between the shell-structured clusters and spherical finite bcc lattices with relaxed surfaces, the former and the latter being the ground states for small systems and for the large enough systems, respectively. It is shown that, when N > N(c)(N(c) > N), finite bcc lattices with relaxed surfaces (the shell structures) have stronger cohesion than the shell structures (finite bcc lattices with relaxed surfaces) and the critical value of the transition N(c) is estimated to be 10(4) < N(c) < 1.4 × 10(4) . The nucleation of the bcc lattice in the shell-structured cluster of 2 × 10(4) ions is observed.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2001-12
36巻
1号
開始ページ 41
終了ページ 49
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 80015112663
JaLCDOI 10.18926/47000
フルテキストURL mfe_36_1_051_057.pdf
著者 Vaillancourt, Chico|
抄録 This is a brief essay on using kinesthetic approaches to learning English as a second language. In the essay, I briefly discuss teaching philosophy and 2 small-scale Technical Engineering projects that I have introduced and completed with my 4(th) year engineering students in the spring of 2001.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2001-12
36巻
1号
開始ページ 51
終了ページ 57
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120003497026
JaLCDOI 10.18926/14053
フルテキストURL Mem_Fac_Eng_OU_42_1.pdf
著者 Asatani Jun| 甲本 卓也| Toru Fujiwara| Tadao Kasami|
抄録 Two typical examples, the (32, 21, 6) and (64, 45, 8) extended code of primitive permuted BCH codes, are considered. The sets of minimum weight codewords are analyzed in terms of Boolean polynomial representation. They are classied by using their split weight structure with respect to the left and right half trellis sections, and for each class, the standard form is presented. Based on the results, we can generate a proper list of the minimum weight codewords of the codes.
キーワード Boolean polynomial representation extended BCH codes minimum weight codewords binary shift invariance property
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2008-01
42巻
1号
開始ページ 1
終了ページ 9
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308333
JaLCDOI 10.18926/14120
フルテキストURL Mem_Fac_Eng_OU_40_1_36.pdf
著者 内田 厚| 東辻 千枝子| 鶴田 健二| 東辻 浩夫|
抄録 We present a Stochastic-Difference-Equation (SDE) approach to long time-scale molecular dynamics (MD) simulations, which are required for nanosecond-scale phenomena. In this method, the MD trajectory in a fixed time period is obtained as a stationary solution of an action functional based on an error accumulation of the equation of motion along the path, thus reducing the problem to a boundary-value problem, instead of an initial-value problem in the ordinary MD method. We apply the method to formation processes of Cu thin film via nanocluster deposition onto a substrate. The applicability of the SDE algorithm to the problem and the effects of the choice of SDE parameters on the optimization processes of configuration pathway are examined.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 2006-01
40巻
1号
開始ページ 36
終了ページ 39
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308517