American Chemical Society (ACS)Acta Medica Okayama1932-744712752023Uniform Formation of a Characteristic Nanocomposite Structure of Biogenous Iron Oxide for High Rate Performance as the Anode of Lithium-Ion Batteries22232230ENMasakuniTakahashiGraduate School of Natural Science and Technology, Okayama UniversityRyoSakumaGraduate School of Natural Science and Technology, Okayama UniversityHidekiHashimotoGraduate School of Natural Science and Technology, Okayama UniversityTatsuoFujiiGraduate School of Natural Science and Technology, Okayama UniversityJunTakadaGraduate School of Natural Science and Technology, Okayama UniversityRecently, Fe2O3 has been considered as an alternative anode material for lithium-ion batteries (LIBs) owing to its high theoretical capacity (approximately 1000 mA h g-1), low cost, and nontoxicity. However, its rate performance remains poor relative to that of the conventional graphite anode. In this study, Fe2O3-based anodes were prepared through the annealing of biogenous Fe2O3 (L-BIOX) samples produced by an aquatic Fe-oxidizing bacterium. The effect of the annealing temperature on the performance of the synthesized Fe2O3-based material as the anode of an LIB was investigated. Electrochemical measurements revealed that the annealed L-BIOX samples at 300-700 degrees C exhibited higher rate performances than the unannealed material. Particularly, the sample annealed at 700 degrees C exhibited the highest capacity among the synthesized materials and showed a higher performance than the previously reported Fe2O3-based anodes. It exhibited a capacity of 923 mA h g-1 even at a high current density of 2 A g-1. After annealing at 700 degrees C and discharging, the synthesized biogenous material had a uniform nanocomposite structure composed of alpha-Fe2O3 nanoparticles dispersed in an amorphous matrix of Li-Si-P oxide. To form this uniform nanostructure, the solid-state diffusion resistance of the Li+ ions in the active material was reduced, which consequently improved the rate performance of the electrode. Therefore, this study provides substantial insights into the development and improvement of the performance of novel Fe2O3-based nanomaterials as the anode of LIBs.No potential conflict of interest relevant to this article was reported.ElsevierActa Medica Okayama138824811042019Bipolar anodic electrochemical exfoliation of graphite powders106475ENHidekiHashimotoDepartment of Applied Chemistry, School of Advanced Engineering, Kogakuin UniversityYusukeMuramatsuDepartment of Applied Chemistry, School of Advanced Engineering, Kogakuin UniversityYutaNishinaResearch Core for Interdisciplinary Sciences, Okayama UniversityHidetakaAsohDepartment of Applied Chemistry, School of Advanced Engineering, Kogakuin UniversityThe electrochemical exfoliation of graphite has attracted considerable attention as a method for large-scale, rapid production of graphene and graphene oxide (GO). As exfoliation typically requires direct electrical contact, and is limited by the shape and/or size of the starting graphite, treatment of small graphite particles and powders, the typical form available commercially, is extremely difficult. In this study, GO nanosheets were successfully prepared from small graphite particles and powders by a bipolar electrochemical process. Graphite samples were placed between two platinum feeder electrodes, and a constant current was applied between the feeder electrodes using dilute sulfuric acid as the electrolyte. Optical microscopy, atomic force microscopy, X-ray diffractometry, Raman spectroscopy, and X-ray photoelectron spectroscopy were employed to examine the samples obtained after electrolysis. The results obtained from these analyses confirmed that anodic electrochemical exfoliation occurs in the graphite samples, and the exfoliated samples are basically highly crystalline GO nanosheets with a low degree of oxidation (C/O = 3.6–5.3). This simple electrochemical method is extremely useful for preparing large amounts of graphene and GO from small particles of graphite.No potential conflict of interest relevant to this article was reported.Acta Medica Okayama0008-62234942011Exfoliated graphene sheets decorated with metal / metal oxide nanoparticles: simple preparation from cation exchanged graphite oxide11181125ENKazumaGotohTaroKinumotoEijiFujiiAkiYamamotoHidekiHashimotoTakahiroOhkuboAtsushiItadaniYasushigeKurodaHiroyukiIshidaWe produced carbon hybrid materials of graphene sheets decorated with metal or metal oxide nanoparticles of gold, silver, copper, cobalt, or nickel from cation exchanged graphite oxide. Measurements using powder X-ray diffraction, transmission electron microscopy, and X-ray absorption spectra revealed that the Au and Ag in the materials (Au-Gr and Ag-Gr) existed on graphene sheets as metal nanoparticles, whereas Cu and Co in the materials (Cu-Gr and Co-Gr) existed as a metal oxide. Most Ni particles in Ni-Gr were metal, but the surfaces of large particles were partly oxidized, producing a core-shell structure. The Ag-Gr sample showed a catalytic activity for the oxygen reduction reaction in 1.0 M KOH aq. under an oxygen atmosphere. Ag-Gr is superior as a cathode in alkaline fuel cells, which should not be disturbed by the methanol cross-over problem from the anode. We established an effective approach to prepare a series of graphene-nanoparticle composite materials using heat treatment.No potential conflict of interest relevant to this article was reported.