JaLCDOI 10.18926/47028
FullText URL mfe_36_2_073_082.pdf
Author Hidayat, Iip Syarif| Toyota, Yoshitaka| Torigoe, Osamu| Wada, Osami| Koga, Ryuji|
Abstract A multi-path ring-resonator (MPRR) was proposed to extend FSR of ring resonator. However, it is complicated to analyze the MPRR by using well-known analysis techniques such as scattering matrix or other numerical methods. This paper describes procedure for deriving transfer matrix by means of signal flow-chart to analyze the MPRR. We do not need complicated calculation for steady state analysis because transfer matrix elements are formulated clearly. As a result, The calcultaion time in this method can be reduced 1/3 to 1/20 times compared with using scattering matirx method. Furthermore, a transmittance characteristics of the MPRR at FSR extension-factor of 10 will also be shown. This suggests that analysis of other types of the MPRR by using this method can be performed simply and take a shorter time.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2002-03
Volume volume36
Issue issue2
Start Page 73
End Page 82
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003497050
JaLCDOI 10.18926/47026
FullText URL mfe_36_2_061_066.pdf
Author Yamagiwa, Masashi| Namba, Akitoshi| Akao, Tetsuyuki| Mizuki, Eiichi| Ohba, Michio| Sakai, Hiroshi|
Abstract The crystal proteins produced by Bacillus thuringiensis subsp, israelensis (Bti) and subsp. coreanensis A1519 strain were examined for the cytotoxicity against MOLT-4 and HeLa cells by MTT assay and LDH assay, The A1519 crystal proteins processed by proteinase K exhibited the specific cell-killing activity toward MOLT-4 with little damage to the cell membrane, On the other hand, the Bti crystal proteins processed by proteinase K caused the substantial damage to the cell membrane of both MOLT-4 and HeLa, leading to the cell lysis. The non-digested crystal proteins of both strains exhibited no cytotoxicity, These data suggested that while the Bti crystal proteins caused the colloid-osmotic swelling and cell lysis of MOLT-4 and HeLa, the proteinase K-digested A1519 crystal proteins induced the specific cell death of MOLT-4 through a mechanism other than that of Bti.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2002-03
Volume volume36
Issue issue2
Start Page 61
End Page 66
ISSN 0475-0071
language 英語
File Version publisher
NAID 80015582224
JaLCDOI 10.18926/47024
FullText URL mfe_36_2_043_049.pdf
Author Vaillancourt, Chico|
Abstract In this case study, I will analyse and discuss the results of a survey concerning motivation towards learning a second language conducted in four Canadian schools. This section, part one of the study, was conducted in the Sudbury Region of Ontario, Canada. This region of the world was chosen because bilingualism is quite common there and a large portion of the community has learned a second language. Part two will be conducted in the winter of 2002, in Denmark, a European country that neighbours many countries with different mother tongues, I hope to conclude this case study with part three in the summer of 2002, in Japan, a monolingual island nation.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2002-03
Volume volume36
Issue issue2
Start Page 43
End Page 49
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003497045
JaLCDOI 10.18926/47023
FullText URL mfe_36_2_015_042.pdf
Author Ohtani, Ryuji| Konishi, Masami| Imai, Jun| Nishi, Tatsushi|
Abstract In this paper, we studied a planning and scheduling of production system considering demand changes. In the proposed system, planning part determines lot-size and amount of jobs in production. On the other hand, scheduling part determines the production sequence of jobs. In order to treat with the demand changes, both planning and scheduling should work well simultaneously. In the proposed system, preset and real time production control system is newly constructed from the view point of adaptive control. In the system, production planning is modified when the difference between production amount and demand becomes large. Moreover, production schedule is regenerated when the determined schedule is deviated from the prospected one. The scheduling system is characterized as the autonomous decentralized optimization system where each job works as agent and agent searches its appropriate starting time of processing. The effectiveness of the proposed system is confirmed by numerical examples.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2002-03
Volume volume36
Issue issue2
Start Page 15
End Page 42
ISSN 0475-0071
language 英語
File Version publisher
NAID 80015471209
JaLCDOI 10.18926/47022
FullText URL mfe_36_2_007_013.pdf
Author Abe, Takeji| Nagao, Makoto| Ohta, Tomoyuki| Nagayama, Noriyuki|
Abstract It is important to study the microscopic deformation behavior of inhomogeneous material, for most engineering materials are inhomogeneous. The aim of the present study is to clarify by numerical analysis some features of microscopic plastic strain distributions, the mean flow stress and the material factors affecting on it. The rigid-plastic solution is important not only for plastic deformation problems with large strain, but also for creep deformation problems through the plastic analogy in the creep analysis. The effects of material parameter and loading conditions on the deformation behavior of the material are examined and discussed based on the result of calculation. The effects of the aspect ratio of the inhomogeneous regions on the deformation mode are studied. The patterns of the strain concentration and the averaged flow stress of the inhomogeneous material are also discussed. The results of rigid-plastic material are compared with those of the elastic material.
Keywords Plasticity Deformation Inhomogeneous Material Strain Concentration Coefficient Rigid-Plastic FEM
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2002-03
Volume volume36
Issue issue2
Start Page 7
End Page 13
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003497044
JaLCDOI 10.18926/47021
FullText URL mfe_36_2_001_006.pdf
Author Sakakibara, Akira| Kanadani, Teruto| Tashiro, Tsutomu| Yoshioka, Kazumi|
Abstract The effect of heat-treatment conditions on occurrence of serration in Al-Zn alloys was investigated. Specimens were aged for various times up to 2.6Ms at 293K or 273K after quenching from various temperatures (T(Q)), 473K to 853K, and tensile-tested at room temperature. Serration occurred more easily according as T(Q) became lower and the aging time became shorter: in the case that T(Q)=473K serration was observed even after aging for 2.6Ms, while in the case that T(Q)=773K serration did not occur irrespective of aging conditions. Serration was also recognized when the specimens were furnace-cooled from 773K to room temperature. These results together with those obtained by the electrical resistometry suggest that the serration in the low'concentrated Al-Zn alloy is caused by the formation of small GP zones whose Guinier radius is less than 1nm or some sort of solute clusters.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2002-03
Volume volume36
Issue issue2
Start Page 1
End Page 6
ISSN 0475-0071
language 英語
File Version publisher
NAID 80015497758
JaLCDOI 10.18926/47004
FullText URL mfe_36_1_107_116.pdf
Author Kanatani, Kenichi| Ohta, Naoya|
Abstract We present a new method for automatically detecting circular objects in images: we detect an osculating circle to an elliptic arc using a Hough transform, iteratively deforming it into an ellipse, removing outlier pixels, and searching for a separate edge. The voting space is restricted to one and two dimensions for efficiency, and special weighting schemes are introduced to enhance the accuracy. We demonstrate the effectiveness of our method using real images. Finally, we apply our method to the calibration of a turntable for 3-D object shape reconstruction.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-12
Volume volume36
Issue issue1
Start Page 107
End Page 116
ISSN 0475-0071
language 英語
File Version publisher
NAID 80012855284
JaLCDOI 10.18926/47003
FullText URL mfe_36_1_091_106.pdf
Author Kanatani, Kenichi| Ohta, Naoya|
Abstract We present a theoretically optimal linear algorithm for 3-D reconstruction from point correspondences over two views. We also present a similarly constructed optimal linear algorithm for 3-D reconstruction from optical flow. We then compare the performance of the two algorithms by simulation and real-image experiments using the same data. This is the first impartial comparison ever done in the sense that the two algorithms are both optimal, extracting the information contained in the data to a maximum possible degree. We observe that the finite motion solution is always superior to the optical flow solution and conclude that the finite motion algorithm should be used for 3-D reconstruction.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-12
Volume volume36
Issue issue1
Start Page 91
End Page 106
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003497029
JaLCDOI 10.18926/47002
FullText URL mfe_36_1_079_090.pdf
Author Kanatani, Kenichi|
Abstract We first present an improvement of Kanatani's subspace separation [8] for motion segmentation by newly introducing the affine space constraint. We point out that this improvement does not always fare well due to the effective noise it introduces. In order to judge which solution to adopt if different segmentations are obtained, we present two criteria: one is the standard F test; the other is model selection using the geometric AIC of Kanatani [7] and the geometric MDL of Matsunaga and Kanatani [13]. We test these criteria doing real image experiments.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-12
Volume volume36
Issue issue1
Start Page 79
End Page 90
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003497028
JaLCDOI 10.18926/47001
FullText URL mfe_36_1_059_077.pdf
Author Kanatani, Kenichi|
Abstract Contrasting "geometric fitting", for which the noise level is taken as the asymptotic variable, with "statistical inference", for which the number of observations is taken as the asymptotic variable, we give a new definition of the "geometric AIC" and the "geometric MDL" as the counterparts of Akaike's AIC and Rissanen's MDL. We discuss various theoretical and practical problems that emerge from our analysis. Finally, we show, doing experiments using synthetic and real images, that the geometric MDL does not necessarily outperform the geometric AIC and that the two criteria have very different characteristics.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-12
Volume volume36
Issue issue1
Start Page 59
End Page 77
ISSN 0475-0071
language 英語
File Version publisher
NAID 80012855281
JaLCDOI 10.18926/47000
FullText URL mfe_36_1_051_057.pdf
Author Vaillancourt, Chico|
Abstract This is a brief essay on using kinesthetic approaches to learning English as a second language. In the essay, I briefly discuss teaching philosophy and 2 small-scale Technical Engineering projects that I have introduced and completed with my 4(th) year engineering students in the spring of 2001.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-12
Volume volume36
Issue issue1
Start Page 51
End Page 57
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003497026
JaLCDOI 10.18926/46999
FullText URL mfe_36_1_041_049.pdf
Author Totsuji, Hiroo| Kishimoto, Tokunari| Totsuji, Chieko| Tsuruta, Kenji|
Abstract The ground state of spherical clusters of charged particles of one species confined by the three-dimensional parabolic potential is investigated by molecular dynamics simulations with the system size from N = 5000 to N = 1.2 × 10(5) . The cohesive energy per particle is compared between the shell-structured clusters and spherical finite bcc lattices with relaxed surfaces, the former and the latter being the ground states for small systems and for the large enough systems, respectively. It is shown that, when N > N(c)(N(c) > N), finite bcc lattices with relaxed surfaces (the shell structures) have stronger cohesion than the shell structures (finite bcc lattices with relaxed surfaces) and the critical value of the transition N(c) is estimated to be 10(4) < N(c) < 1.4 × 10(4) . The nucleation of the bcc lattice in the shell-structured cluster of 2 × 10(4) ions is observed.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-12
Volume volume36
Issue issue1
Start Page 41
End Page 49
ISSN 0475-0071
language 英語
File Version publisher
NAID 80015112663
JaLCDOI 10.18926/46998
FullText URL mfe_36_1_029_039.pdf
Author Imai, Jun| Wada, Kiyoshi|
Abstract A procedure for control-oriented modeling is proposed for large flexible structures with unknown modal parameters. Techniques on quantification of errors in modal truncated nominal models are developed for the case where a finite number of upper and lower bounds of the unknown modal parameters are given. A feasible set of systems matching the conditions is introduced, and then error bounds covering the feasible set are established in the frequency domain. The bounds are easily checked using linear programming for any user-specified frequency. The feasibility of the proposed scheme is illustrated by numerical study on an ideal flexible beam example.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-12
Volume volume36
Issue issue1
Start Page 29
End Page 39
ISSN 0475-0071
language 英語
File Version publisher
NAID 80012887118
JaLCDOI 10.18926/46997
FullText URL mfe_36_1_017_028.pdf
Author Endo, Shinichiro| Konishi, Masami|
Abstract Small Scale Hydroelectric Power Generation is made using the water drop caused by the gradient difference between that of the river and that of the penstock. The water flow in this system apt to vary with time. Especially, at the time of the flood or that of the dry, the flow in the water stream varies largely. To realize the stable generation, it is necessary to maintain the water level in the head tank located in the mid way in the stream channel at a constant level. In this paper, variation of water level is forecasted using two-tank model for the penstock and the head tank and the water level control algorithm is proposed by deadbeat control. The effectiveness of the algorithm is evaluated beforehand using the simulation program of the water environment for the hydroelectric generation system.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-12
Volume volume36
Issue issue1
Start Page 17
End Page 28
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003497023
JaLCDOI 10.18926/46996
FullText URL mfe_36_1_007_016.pdf
Author Li, Yan| Abe, Takeji| Tada, Naoya| Kanazawa, Masanori|
Abstract The change in the surface morphology of polycrystalline titanium during tensile plastic deformation is studied, using the scanning probe microscope as well as the laser scanning microscope. The observation shows that the slip occurs mainly near grain boundary at the strain range of ε < 0.05. The slip develops with the applied strain, and the slip on the second slip system or the crossing of slip lines appear. The surface roughness increases linearly with the applied strain. The height difference between the grain boundary area and the inner grain area also increases with the applied strain, though the increase rate becomes low after the applied strain of about 0.3. The nano-scale height difference of the surface step of slip lines increases with the applied strain, though it remains almost constant after the applied strain of 0.4. The averaged surface roughness measured with the scanning probe microscope is in good agreement with that measured with the laser scanning microscope.
Keywords Plasticity Polycrystalline Titanium Tensile Deformation Surface Morphology Slip Twin Probe Scanning Microscope Laser Scanning Microscope
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-12
Volume volume36
Issue issue1
Start Page 7
End Page 16
ISSN 0475-0071
language 英語
File Version publisher
NAID 80012831215
JaLCDOI 10.18926/46983
FullText URL mfe_37_2_089_097.pdf
Author Iokibe, Kengo| Toyota, Yoshitaka| Wada, Osami| Koga, Ryuji|
Abstract Aerosol extinction coefficients of clouds and dust were continuously measured in the year of 2002 with a polarized Mie-scattering lidar controlled by an automatic and remotely operating system utilizing internet services. Measured cloud extinctions were greater than 1.0 km(-1) below the altitude 6 km, 0.17 - 1.0 km(-1) between 6 and 10 km, and 0.091 - 0.3 km(-1) beyond 10km. Extinction of dust were 0.10 and 0.20 km(-1) for Asian dust and 0.057 km(-1) for urban dust.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2003-03
Volume volume37
Issue issue2
Start Page 89
End Page 97
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003457336
JaLCDOI 10.18926/46982
FullText URL mfe_37_2_073_087.pdf
Author Nogami, Yasuyuki| Morikawa, Yoshitaka|
Abstract Public key cryptosystem has many uses, such as to sign digitally, to realize electronic commerce. Especially, RSA public key cryptosystem has been the most widely used, but its key for ensuring sufficient security reaches about 2000 bits long. On the other hand, elliptic curve cryptosystem(ECC) has the same security level with about 7-fold smaller length key. Accordingly, ECC has been received much attention and implemented on various processors even with scarce computation resources. In this paper, we deal with an elliptic curve which is defined over extension field F(p2c) and has a prime order, where p is the characteristic and c is a non negative integer. In order to realize a fast software implementation of ECC adopting such an elliptic curve, a fast implementation method of definition field F(p2c) especially F(p8) is proposed by using a technique called successive extension. First, five fast implementation methods of base field F(p2) are introduced. In each base field implementation, calculation costs of F(p2)-arithmetic operations are evaluated by counting the numbers of F(p)-arithmetic operations. Next, a successive extension method which adopts a polynomial basis and a binomial as the modular polynomial is proposed with comparing to a conventional method. Finally, we choose two prime numbers as the characteristic, and consider several implementations for definition field F(p8) by using five base fields and two successive extension methods. Then, one of these implementations is especially selected and implemented on Toshiba 32-bit micro controller TMP94C251(20MHz) by using C language. By evaluating calculation times with comparing to previous works, we conclude that proposed method can achieve a fast implementation of ECC with a prime order.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2003-03
Volume volume37
Issue issue2
Start Page 73
End Page 87
ISSN 0475-0071
language 英語
File Version publisher
NAID 80015999992
JaLCDOI 10.18926/46981
FullText URL mfe_37_2_067_072.pdf
Author Yamagiwa, Masashi| Sakai, Hiroshi|
Abstract An active form of Cry4A is a heterodimer of the 20- and 45-kDa fragments that are derived from the 130-kDa Cry4A protoxin. To investigate the function of these two fragments, several deletion mutants were constructed and expressed in E.coli as the GST (glutathione-S-transferase) fusion proteins. The results of the bioassay against Culex pipiens larvae showed that the interaction of two fragments of Cry4A was necessary for the toxicity, and that the C-terminal 67 amino acids of the 20-kDa fragment corresponding to the helices α4 and α5 were involved in determining the insecticidal activity. Surprisingly the lack of helix α5 did not affect the toxicity to C. pipiens, suggesting that the role of helix α5 of Cry4A was different from that postulated in the case of Cry4A toxins.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2003-03
Volume volume37
Issue issue2
Start Page 67
End Page 72
ISSN 0475-0071
language 英語
File Version publisher
NAID 80016019143
JaLCDOI 10.18926/46980
FullText URL mfe_37_2_061_066.pdf
Author Vaillancourt, Chico|
Abstract In this case study, I will analyse and discuss the results of a survey concerning motivation towards learning a second language conducted in one Danish high school. The students surveyed were between the ages of 13-18. This section, part two of the study, was conducted in Copenhagen, Denmark. This region of the world was chosen because bilingualism is quite common there and a large portion of the school-aged community is learning a second language and often a third and even a fourth. Denmark, a European country, is different than Canada (Case Study-Part 1.) because it neighbours many countries, which use different mother tongues.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2003-03
Volume volume37
Issue issue2
Start Page 61
End Page 66
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003457333
JaLCDOI 10.18926/46979
FullText URL mfe_37_2_045_060.pdf
Author Xu, Wei| Zhao, Y.| Horikane, T.| Hayata, T.| Tosuji, H.| Kagawa, Y.|
Abstract Resistivity distribution sounding of the non-homogeneous earth is important for electrical ground system design, geophysical prospecting and survey or monitoring the groundwater flow level. The previous paper presented that the direct inversion of the electric resistivity distribution in a domain is possible from the impedance data measured over the domain boundary using the dual reciprocity boundary element modelling in two-dimentional field [1]. The proposed inversion technique is extended to the distribution in three-dimensional space [2]. This technique is capable of inversion without iteration and meshing of the domain. Electric field with spatially varying conductivity is governed by Laplace equation, which is transformed into a Poisson-type expression with an inhomogeneous term involving the conductivity difference as a source term. Dual reciprocity method (DRM) is a technique for transforming the domain integral associated with the inhomogeneous term in Poisson equation into the boundary integral expression. The resistivity distribution in the field can thus be identified from the data observed over its boundary, for which some examples are demonstrated [2]. In this paper, the examination is extended to the case where only the data measured over the single surface is used for the inversion.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2003-03
Volume volume37
Issue issue2
Start Page 45
End Page 60
ISSN 0475-0071
language 英語
File Version publisher
NAID 80016037881