JaLCDOI 10.18926/15403
FullText URL Mem_Fac_Eng_OU_27_2_19.pdf
Author Nara, Shigetoshi| Totsuji, Hiroo|
Abstract Numerical simulations of a single layer recurrent neural network model in which the synaptic connection matrix is formed by summing cyclic products of succesive patterns show that complex dynamics can occur with the reduction of a connectivity parameter which is the number of connection between neurons. The structure in these dynamics is discussed from the viewpoint of realizing complex function using complex dynamics.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1993-03-25
Volume volume27
Issue issue2
Start Page 19
End Page 40
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002307451
JaLCDOI 10.18926/19632
FullText URL Mem_Fac_Eng_OU_32_7.pdf
Author Adli| Yamamoto, Yoshitake|
Abstract This paper describes a new measurment method and principle of power line interference elimination in ECG signal using inverse loop and AC power line configuration (APC). First, we considered that magnetic induction effect not only depend on a conductive loop area that formed by shielded wires that connect the object and amplifier but also effect of body area effective must be considered. It is simple and useful because interference can be eliminated to very small value show that the condition and it can be applied in a real ECG signal recording. Second, results show that the contribution of displacement currents into the object especially APC in vertical configuration is smaller than it in other one. Because this method is so easy that it is convenient to be used to understand some aspects of power line interference elimination phenomenon. Hence we expect that this method can be used as one of improvement method in measurement system of ECG signal recording.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1998-04-20
Volume volume32
Issue issue1-2
Start Page 7
End Page 14
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002309065
JaLCDOI 10.18926/46954
FullText URL mfe_38_1-2_073_089.pdf
Author Kenmochi, Yukiko| Imiya, Atsushi|
Abstract Boundary tracking and surface generation are ones of main topological topics for three-dimensional digital image analysis. However, there is no adequate theory to make relations between these different topological properties in a completely discrete way. In this paper, we present a new boundary tracking algorithm which gives not only a set of border points but also the surface structures by using the concepts of combinatorial/algebraic topologies. We also show that our boundary becomes a triangulation of border points (in the sense of general topology), that is, we clarify relations between border points and their surface structures.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2004-03
Volume volume38
Issue issue1-2
Start Page 73
End Page 89
ISSN 0475-0071
language 英語
File Version publisher
NAID 80016889444
JaLCDOI 10.18926/15458
FullText URL Mem_Fac_Eng_OU_28_2_33.pdf
Author Wang, Ming| Ahmed, Anis| Wada, Osami| Koga, Ryuji|
Abstract Proposed here is a convenient optical system to collimate the crescent shaped blue laser beam radiated from a Cerenkov SHG in channel waveguide configuration. This collimation system is consisted of a parabolic mirror and has a very large tolerance to the mirror displacement. The anisotropy of the nonlinear crystal on which the waveguide is fabricated has been taken into account. The optimum mirror location is given to obtain a collimated blue laser beam with an aberration less than 0.07λ. By using an objective lens, the collimated beam can be focused down to a thin beam with the spot size less than 1μm.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1994-03-15
Volume volume28
Issue issue2
Start Page 33
End Page 44
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002307149
JaLCDOI 10.18926/15452
FullText URL Mem_Fac_Eng_OU_28_2_9.pdf
Author Sakakibara, Akira| Kanadani, Teruto| Nakagawa, K.| Yokota, Y.|
Abstract The state above the solubility temperature of GP zones of Al-3mass % Mg alloy, which has a tendency for precipitation and preprecipitation at low temperature, was studied by resistivity measurement. Homogenization treatment at high temperature reduced Mg atoms in the surface layer. After quenching from 623K, the specimen was annealed sequentially at various temperatures above the GP zone solvus. The stationary resistivity obtained in annealing at a temperature was the same irrespective of the starting state and increased with decreasing annealing temperature. No precipitation was observed in the annealing. The results are not in favor of the segregation of Mg atoms to the dislocation loops but of the short range clustering.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1994-03-15
Volume volume28
Issue issue2
Start Page 9
End Page 12
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002307581
JaLCDOI 10.18926/15464
FullText URL Mem_Fac_Eng_OU_28_2_77.pdf
Author Osaka, Akiyoshi| Kawamura Haruyuki| Miura, Yoshinari|
Abstract Amorphous films of lead oxyfluorosilicate were prepared with a rf-sputtering technique, and the distribution profiles of the component elements and chemical states of the fluoride ions were analyzed with an X-ray photoelectron spectrometer. Si atoms with an expanded coordination, O(4)Si-F, were present near the surface, and O(3)Si-F units were present in the deeper part of the films. Electrical resistance indicated transition to a conduction state for the films containing fluoride ions, while the films were crystallized to precipitate low quartz by the irradiation of He-Ne laser of 3 mW up to 1 sec.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1994-03-15
Volume volume28
Issue issue2
Start Page 77
End Page 84
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002307766
JaLCDOI 10.18926/15364
FullText URL Mem_Fac_Eng_OU_35_137.pdf
Author Sakiyama, Takaharu| Yoshimi, Tsuyoshi| Miyake, Akira| Umeoka, Midori| Tanaka, Atsushi| Ozaki, Sho| Nakanishi, Kazuhiro|
Abstract A monoacylglycerol lipase (MGL) was purified from Pseudomonas sp. LP7315 by ammonium sulfate precipitation, anion-exchange chromatography, and preparative electrophoresis. The purified enzyme was homogeneous on an SDS-polyacrylamide gel with a molecular mass of 59 kDa. Its hydrolytic activity was confirmed to be specific for monoglycerides: the enzyme did not hydrolyze diand triglycerides. MGL was found to be stable even after l-h incubation at 65℃. The hydrolytic activity depended not only on temperature and pH but also on the type of monoglyceride used. MGL also catalyzed monoglyceride synthesis at 65℃ in a solvent-free two-phase system, in which fatty acid droplets were dispersed in the glycerol phase with a low water content. The synthetic reaction proceeded at a constant rate for approximately 24 h and reached an equilibrium after 48 h of reaction. The initial rate of the synthetic reaction depended on several factors: the type of fatty acid used as the substrate, the amounts of fatty acid and glycerol, and the concentration of MGL in the glycerol phase. To analyze the effects of these factors, a kinetic model was developed based on the assumption that the adsorption equilibrium of MGL molecules at the interface between the two phases is the rate-determining factor for the synthetic reaction. The model was found to yield a good approximation of the initial synthetic rate under various reaction conditions. The analysis suggests that the adsorption behavior of MGL onto the interface had a large effect on the initial rate of the monoglyceride synthesis.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-03-27
Volume volume35
Issue issue1-2
Start Page 137
End Page 146
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002307705
JaLCDOI 10.18926/15499
FullText URL Mem_Fac_Eng_OU_24_2_49.pdf
Author Mori, Chuji| Machida Ken-ichi|
Abstract Distance measurements have been more and more easy and accurate to carry out, and it is expected that distance mesurements may provide rather accurate results than angle measurements. Under these circumstances, caracteritics of errors in typical trilateration nets are investigated. The nets investigated are as follows: From single row of chains to pranimetrically extended nets in figure, open and closed networks with respect to external constraint, and with and without as to internal constraint. Computations are performed by use of the method of condition equations, and behaviours of error propagation and errors of coordinates of stations in the nets are shown in case of typical nets. For example, effects for decrease in error by composing a double row of chains and by enforcing external constraints are explained.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1990-03-29
Volume volume24
Issue issue2
Start Page 49
End Page 65
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002307544
JaLCDOI 10.18926/48126
FullText URL mfe_046_010_020.pdf
Author Kanatani, Kenichi|
Abstract We present a new technique for calibrating ultra-wide fisheye lens cameras by imposing the constraint that collinear points be rectified to be collinear, parallel lines to be parallel, and orthogonal lines to be orthogonal. Exploiting the fact that line fitting reduces to an eigenvalue problem, we do a rigorous perturbation analysis to obtain a Levenberg-Marquardt procedure for the optimization. Doing experiments, we point out that spurious solutions exist if collinearity and parallelism alone are imposed. Our technique has many desirable properties. For example, no metric information is required about the reference pattern or the camera position, and separate stripe patterns can be displayed on a video screen to generate a virtual grid, eliminating the grid point extraction processing.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2012-01
Volume volume46
Start Page 10
End Page 20
ISSN 1349-6115
language 英語
Copyright Holders Copyright © by the authors
File Version publisher
NAID 80022451621
JaLCDOI 10.18926/44497
FullText URL mfe_045_027_036.pdf
Author Kanatani, Kenichi| Sugaya, Yasuyuki|
Abstract We describe in detail the algorithm of bundle adjustment for 3-D reconstruction from multiple images based on our latest research results. The main focus of this paper is on the handling of camera rotations and the efficiency of computation and memory usage when the number of variables is very large; an appropriate consideration of this is the core of the implementation of bundle adjustment. Computing the fundamental matrix from two views and reconstructing the 3-D structure from multiple views, we evaluate the performance of our algorithm and discuses technical issues of bundle adjustment implementation.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2011-01
Volume volume45
Start Page 27
End Page 35
ISSN 1349-6115
language 英語
Copyright Holders Copyright © by the authors
File Version publisher
NAID 80021759249
JaLCDOI 10.18926/19594
FullText URL Mem_Fac_Eng_OU_31_2_39.pdf
Author Imayoshi Naoki| Hayakawa, Satoshi| Ohtsuki, Chikara| Osaka, Akiyoshi|
Abstract Nb(2)O(5)-and Ta(2)O(5)-doped calcium si1icate glasses were soaked for various periods in a simulated body fluid(Kokubo solution) up to 30 days. Apatite formation ability of the surface of these glasses were investigated with thin-film X-ray diffraction and FT-IR reflection spectroscopy. The effects of these additive oxides on the bioactivity of CaO・SiO(2) based glass were discussed. A small amount of Nb(2)O(5) and Ta(2)O(5) suppressed the rate of silica hydrogel layer formation and the apatite formation on the surface of the glasses. The rate of the apatite nucleation on the surface of Nb(2)O(5)-doped calcium silicate glass was slower than that on the surface of Ta(2)O(5)-doped calcium silicate glass. It was concluded that the decrease in the apatite forming ability of calcium silicate glasses by these additive oxides is attributed to the suppression of formation of silica hydrogel layer which plays an important role in apatite nucleation.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1997-03-28
Volume volume31
Issue issue2
Start Page 39
End Page 44
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002309151
JaLCDOI 10.18926/19596
FullText URL Mem_Fac_Eng_OU_31_2_45.pdf
Author Osaka, Akiyoshi| Kobayashi Keizo| Hayakawa, Satoshi| Ohtsuki, Chikara|
Abstract The thermal expansion coefficient of some bioactive glasses in the system CaO-SiO(2)-B(2)O(3) were adjusted to be similar to that of titanium by controlling the composition. A glass of composition 45CaO・30SiO(2)・25B(2)O(3) was selected among those as the enameling glass. A slurry was prepared by mixing the glass powder and ethanal to be developed on titanium and heated at 740℃ for 30 min. Thus treated specimen was soaked in a simulated body fluid (Kokubo solutiion). FT-IR reflection and thin film X-ray diffraction analyses indicated apatite formation on the glass coating layer within 12 h of soaking in the fluid. Thus titanium could be provided with bioactivity due to the enameling.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1997-03-28
Volume volume31
Issue issue2
Start Page 45
End Page 51
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002309181
JaLCDOI 10.18926/15495
FullText URL Mem_Fac_Eng_OU_24_2_31.pdf
Author Oka, Hisao| Isayama Yoshiharu| Nakauchi Makoto| Yamamoto, Tatsuma|
Abstract A small vibration on the body surface is expected to apply to a clinical examination of the autonomic nervous system. The vibration cannot be found by the naked eyes. It is called a microvibration (MV) or a minor tremor (MT). It is not cleared out why and how the MV occurs, but many papers about its occurrence and clinical application have been published. In this study, the typical spectrum of MV and the various causes of MV occurrence are studied. The relationships of MV with heart rate, muscle contraction and MV are discussed. The power spectrum of MV is obtained by using an autoregressive model.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1990-03-29
Volume volume24
Issue issue2
Start Page 31
End Page 40
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002307725
JaLCDOI 10.18926/15430
FullText URL Mem_Fac_Eng_OU_29_2_89.pdf
Author Sekoguchi, Kenji| Miyazaki, Shigeji|
Abstract The present paper deals with a new perfomance measure, the actual mean flow time, defined as a mean of the elapsed time of each job counted from the start time on a schedule to the corresponding due date. For the one machine backward scheduling model with a common due date and independent setup times, LPT schedule is shown as the optimal solution for the proposed measure. An optimal algorithm is presented for the case with dependent setup times on the basis of the algorithm by Arcelus and Chandra for a n / 1 / F forward scheduling problem. The proposed algorithm is coded in C-language and a computational experience is reported through a 16-bit computer.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1995-03-27
Volume volume29
Issue issue2
Start Page 89
End Page 94
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002307729
JaLCDOI 10.18926/47004
FullText URL mfe_36_1_107_116.pdf
Author Kanatani, Kenichi| Ohta, Naoya|
Abstract We present a new method for automatically detecting circular objects in images: we detect an osculating circle to an elliptic arc using a Hough transform, iteratively deforming it into an ellipse, removing outlier pixels, and searching for a separate edge. The voting space is restricted to one and two dimensions for efficiency, and special weighting schemes are introduced to enhance the accuracy. We demonstrate the effectiveness of our method using real images. Finally, we apply our method to the calibration of a turntable for 3-D object shape reconstruction.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2001-12
Volume volume36
Issue issue1
Start Page 107
End Page 116
ISSN 0475-0071
language 英語
File Version publisher
NAID 80012855284
JaLCDOI 10.18926/46971
FullText URL mfe_37_1_041_049.pdf
Author Sugaya, Yasuyuki| Kanatani, Kenichi|
Abstract We study the problem of segmenting independently moving objects in a video sequence. Several algorithms exist for classifying the trajectories of the feature points into independent motions, but the performance depends on the validity of the underlying camera imaging model. In this paper, we present a scheme for automatically selecting the best model using the geometric AIC before the segmentation stage, Using real video sequences, we confirm that the segmentation accuracy indeed improves if the segmentation is based on the selected model. We also show that the trajectory data can be compressed into low-dimensional vectors using the selected model. This is very effective in reducing the computation time for a long video sequence.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2002-11
Volume volume37
Issue issue1
Start Page 41
End Page 49
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003457326
JaLCDOI 10.18926/15416
FullText URL Mem_Fac_Eng_OU_26_1_43.pdf
Author Bouzidi, Moncef| Koga, Ryuji| Wada, Osami| Kagawa, Naoki| Hai Xu| Kosaka, Megumi| Sano HIroya|
Abstract A numerical technique called as "adjoint spectrum" has been proposed by the authors in a previous work. Two applications of it are presented here. It is demonstrated that by generalizing the aspect of adjoint spectrum it becomes possible to measure densities of mixed gases simultaneously. An experimental proof of this has been carried on and simultaneous measurement of densities of both methane and dinitrogen oxide was realized. On the other hand, it is also reported that frequency shifting of spectra, which is a cause of error in spectrometric measurements, can be corrected by exploiting the adjoint spectrum technique in connection with the Taylor expansion. Numerical examples showing the success of this method are reported as well.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 1991-11-30
Volume volume26
Issue issue1
Start Page 43
End Page 49
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002307796
JaLCDOI 10.18926/47028
FullText URL mfe_36_2_073_082.pdf
Author Hidayat, Iip Syarif| Toyota, Yoshitaka| Torigoe, Osamu| Wada, Osami| Koga, Ryuji|
Abstract A multi-path ring-resonator (MPRR) was proposed to extend FSR of ring resonator. However, it is complicated to analyze the MPRR by using well-known analysis techniques such as scattering matrix or other numerical methods. This paper describes procedure for deriving transfer matrix by means of signal flow-chart to analyze the MPRR. We do not need complicated calculation for steady state analysis because transfer matrix elements are formulated clearly. As a result, The calcultaion time in this method can be reduced 1/3 to 1/20 times compared with using scattering matirx method. Furthermore, a transmittance characteristics of the MPRR at FSR extension-factor of 10 will also be shown. This suggests that analysis of other types of the MPRR by using this method can be performed simply and take a shorter time.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2002-03
Volume volume36
Issue issue2
Start Page 73
End Page 82
ISSN 0475-0071
language 英語
File Version publisher
NAID 120003497050
JaLCDOI 10.18926/14148
FullText URL Mem_Fac_Eng_39_1_28.pdf
Author Ishimaru, Kazuhito| Konishi, Masami| Imai, Jun| Nishi, Tatsushi|
Abstract In reactor furnace, due to high temperature and high pressure, data can be measured only near the furnace wall. In this paper, the way to estimate temperature distribution in a reactor furnace using measured data near the furnace walls and to control temperature distribution to the desired temperature distribution was studied. In the estimation, SQP method is employed using measured data near the furnace walls. As the result, the whole temperature distribution in a furnace could be obtained from such limited data. Furthermore, to control the temperature distribution in a reactor furnace, gas flow from multiple tuyeres and supplying material for controlling temperature distribution in a reactor furnace were determined by the SQP method. It was shown that temperature distribution in a furnace was regulated to achieve various desired distribution. Thus, it was verified that complicated temperature distribution in a reactor furnace could be controlled by combining furnace simulation and SQP method.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2005-01
Volume volume39
Issue issue1
Start Page 28
End Page 39
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002308270
JaLCDOI 10.18926/14146
FullText URL Mem_Fac_Eng_39_1_21.pdf
Author Torigoe, Takashi| Konishi, Masami| Imai, Jun| Nishi, Tatsushi|
Abstract In this paper, neuro based intelligent diagnosis methods for electro-mechanical control system are proposed. A self organizing map neural network (SOM) is used to classify measured data of the target system as a qualitative diagnostic method. Besides of the above procedure, it is expected to attain more efficient maintenance by a quantitative estimation of failure. For the purpose, new method is proposed using a hierarchical neural network (HNN). In the method, classified results by SOM are processed for the quantitative diagnosis. Hierarchical neural network can identify inner structure of the relations between failure causes and its results that enables a quantitative diagnosis.
Publication Title Memoirs of the Faculty of Engineering, Okayama University
Published Date 2005-01
Volume volume39
Issue issue1
Start Page 21
End Page 27
ISSN 0475-0071
language 英語
File Version publisher
NAID 120002308342